• 3D列印服務
  • #maker+t=market
  • COSPLAY 3D 建模
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 巫国勝
2018-12-22 17:56:26

I wanted to print this object. Printing it straight up should be fine or a flat orientation will be good? Which orientation will be the best?

翻譯年糕

Mark Wardle
2018-12-24 02:41:36


原文網址 巫国勝
2018-12-20 19:34:07

Does hollowing means less chance of the build sticking to the FEP sheet? Does hollowing means less chance of the build sticking to the FEP sheet? 翻譯年糕

Mac Calder
2018-12-20 19:37:16

Ivan Antharon Antalec
2018-12-20 20:34:13

Ivan Antharon Antalec
2018-12-20 20:34:59

Chris Cardinal
2018-12-20 21:20:10

巫国勝
2018-12-20 21:22:16

Ivan Antharon Antalec
2018-12-20 21:49:03

巫国勝
2018-12-20 22:05:27

Trea Cotton
2018-12-21 04:03:21

Chris Cardinal
2018-12-21 06:17:10

Jeremy Lauzon
2018-12-21 06:58:27

Sen Kun
2018-12-21 08:13:38

Chris Cardinal
2018-12-21 09:19:50


原文網址 巫国勝
2018-12-20 19:33:33

If the supports turn out fine, but the build went to the FEP. Does it mean more support is needed or is there an underlying hardware issue?

翻譯年糕

Gustaf Sjögren
2018-12-20 20:12:43

Obe Bradford
2018-12-20 21:03:42


原文網址 巫国勝
2018-12-14 22:14:01

any strategy (from the printer pointer of view) to make the prints stay on the platform better? eg. long curing time for the base, shorter curing time on the each individual layer, cleaning the platform after each run, using support structures, cleaning the FEP thouroughly

翻譯年糕

Jaco Norchie Nortje
2018-12-14 22:19:33

巫国勝
2018-12-14 22:21:59

Richard Shapiro
2018-12-14 22:57:31

Richard Shapiro
2018-12-14 22:58:52

巫国勝
2018-12-14 23:07:32

Richard Shapiro
2018-12-14 23:11:06

巫国勝
2018-12-14 23:12:32

Richard Shapiro
2018-12-14 23:14:06

巫国勝
2018-12-15 00:00:19

Richard Shapiro
2018-12-15 00:37:22

Philippe Maegerman
2018-12-15 03:12:09

巫国勝
2018-12-15 10:11:27

巫国勝
2018-12-15 10:12:14

Richard Shapiro
2018-12-15 10:18:00

巫国勝
2018-12-15 10:18:50

巫国勝
2018-12-15 12:40:32

巫国勝
2018-12-15 12:40:35

巫国勝
2018-12-15 14:40:12

Richard Shapiro
2018-12-15 22:24:49

巫国勝
2018-12-17 18:09:01

Sen Kun
2018-12-17 18:18:11


原文網址 巫国勝
2018-12-09 14:58:45

Sometimes my print does not adhere to the platform. Should I increase the exposure time or tune the thickness of the layer?

翻譯年糕

Sen Kun
2018-12-09 15:05:56

巫国勝
2018-12-09 15:07:33

Sen Kun
2018-12-09 15:10:12

巫国勝
2018-12-09 15:10:30

Nick Santana
2018-12-09 15:11:08


原文網址 巫国勝
2018-11-21 20:37:04

anyone tried to use other resins than anycubic's for the build?

翻譯年糕

Artur Fuste
2018-11-21 20:38:49

巫国勝
2018-11-21 20:43:44

巫国勝
2018-11-21 20:44:24

巫国勝
2018-11-21 20:45:53

Al Zamorski
2018-11-21 22:18:39

Paul Tyer
2018-11-22 00:15:50

Zena Andreou
2018-11-22 16:51:39


原文網址 巫国勝
2018-11-20 21:25:20

anyone tried to change the uv source to other wavelengths and try new resins?

翻譯年糕

El Ner Endem
2018-11-20 21:49:11

巫国勝
2018-11-20 21:55:34

Martin Guhl
2018-11-21 00:18:17

巫国勝
2018-11-21 00:22:57

Martin Guhl
2018-11-21 00:44:08

Robert Maefs
2018-11-21 02:41:01

巫国勝
2018-11-21 07:12:39

Robert Maefs
2018-11-21 07:49:48

Philipp Maitrot
2018-11-22 07:29:56

Robert Maefs
2018-11-22 07:36:58

Philipp Maitrot
2018-11-22 08:21:45

巫国勝
2018-11-22 08:22:33

Philipp Maitrot
2018-11-22 08:22:50

巫国勝
2018-11-22 08:23:38

Philipp Maitrot
2018-11-22 08:24:40

Philipp Maitrot
2018-11-22 08:26:19

巫国勝
2018-11-22 08:26:19

巫国勝
2018-11-22 08:27:54

巫国勝
2018-11-22 08:28:27

Philipp Maitrot
2018-11-22 08:31:14

巫国勝
2018-11-22 08:34:57

Philipp Maitrot
2018-11-22 08:41:38

Philipp Maitrot
2018-11-22 08:43:20

巫国勝
2018-11-22 08:44:34

Philipp Maitrot
2018-11-22 08:46:51

巫国勝
2018-11-22 08:48:10

巫国勝
2018-11-22 08:48:51

Philipp Maitrot
2018-11-22 08:48:54


 

討論主題

全不選 常用關鍵字