Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Kurt Camaro
2019-02-18 04:03:25

Parts printed on my Photon, kit built by a friend of mine. Scale 1:87.

翻譯年糕

原文網址 Kurt Camaro
2019-02-07 05:27:53

Assembled model. I think I have to go down to 0,02mm and less exposure time.
Printed with Anycubic gray.

翻譯年糕

原文網址 Kurt Camaro
2019-02-03 23:21:42

First print with Anycubic gray resin. Complete success! B-)

翻譯年糕

Giancarlo Arriola
2019-02-03 23:44:38

Dennis Krüger
2019-02-04 01:27:40

Witek Mazuchowski
2019-02-04 03:48:28

Kurt Camaro
2019-02-04 04:05:11

Patrick James Hash
2019-02-04 04:35:37

Kurt Camaro
2019-02-04 17:21:44

原文網址 Kurt Camaro
2019-01-23 05:56:04

Slowly I start loving this printer :-)

翻譯年糕

Holden8702
2019-01-23 06:28:06

Kurt Camaro
2019-01-24 04:01:20

原文網址 Kurt Camaro
2019-01-22 06:57:06

Finally I got a successfull print. It´s all about the support!

翻譯年糕

Sen Kun
2019-01-22 15:30:41

原文網址 Kurt Camaro
2019-01-13 04:01:30

So here is the print. Like on my first print the models right from the center are not printed, except the support. A few layer have been in the vat, see pictures.
What does this cause?

翻譯年糕

Sen Kun
2019-01-13 04:56:34

Andrea Bigatti
2019-01-13 19:44:33

Kurt Camaro
2019-01-14 01:10:38

原文網址 Kurt Camaro
2019-01-12 06:37:07

Finally I changed to the Chitubox slicer. Auto support looks much better, almost like the auto support in PreForm from Formlabs.
Printing will start tomorrow...

翻譯年糕

Pa Wel
2019-01-12 06:37:43

Jaco Norchie Nortje
2019-01-12 06:37:43

Pa Wel
2019-01-12 06:39:57

Dustin Scott
2019-01-12 06:44:52

Peter Ede
2019-01-12 06:48:14

Antonio Robbins
2019-01-12 06:58:13

Nick Williams
2019-01-12 07:31:44

Nick Williams
2019-01-12 07:32:41

Antonio Robbins
2019-01-12 07:52:27

Joel Ligeiro
2019-01-12 08:15:07

Kurt Camaro
2019-01-12 08:19:39

Kurt Camaro
2019-01-12 08:20:52

谢信福
2019-01-12 10:10:45

Kurt Camaro
2019-01-12 23:47:30

Patrick James Hash
2019-01-13 11:30:11

Philipp Douglas
2019-01-13 15:46:12

Kurt Camaro
2019-01-14 03:46:52

Nikolas Willingham
2019-01-15 02:24:04

原文網址 Kurt Camaro
2019-01-05 06:26:17

Hi folks!
Today I recieved my Photon. First print is done.
50% success. One figure printed perfectly, the other didn't. Just the support and one layer were printed.

翻譯年糕