Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Antonio Robbins
2019-05-25 23:28:28

Updated to new ChiTuBox from Anycubic and perfectly printed supports but no object using Medium setting.

What do I need to change?

翻譯年糕

Chris Rees
2019-05-25 23:37:41

Michael McElrath
2019-05-25 23:38:06

Tommy LeRoy
2019-05-26 07:49:47

Dan Smith
2019-05-26 08:18:10

Antonio Robbins
2019-05-26 08:23:59

原文網址 Antonio Robbins
2019-05-25 05:01:36

I downloaded the beta Chitubox v1.4.0 and it's got more control options than the Anycubic Photon Sliver v1.3.6.

So I can get them set right, what should I put in the Print Settings?
(Also what are the differences between the similar options? Hovering info isn't really specific.)

Light-Off Delay:
Bottom Light-off Delay:

Bottom Lift Distance:
Lifting Distance:

Bottom Lift Speed:
Lifting Speed:
Retraction Speed:

翻譯年糕

Sean O'Hayer
2019-05-25 05:06:43

Sean O'Hayer
2019-05-25 05:11:08

原文網址 Antonio Robbins
2019-04-13 10:10:36

Would the Photon be able to restart a print after power failure if it was added with a software update? Would the Photon be able to restart a print after power failure if it was added with a software update? 翻譯年糕

Eduardo Herrero Ayuso
2019-04-13 10:16:24

Robert Silvers
2019-04-13 10:22:51

Manuel Galán
2019-04-13 11:15:32

Andre Ribeiro
2019-04-13 11:45:08

Jesper Lindhardt
2019-04-13 12:52:17

Antonio Robbins
2019-04-13 13:01:07

Jesper Lindhardt
2019-04-13 13:22:03

David Nicholls
2019-04-13 15:50:03

André Pereira Simões
2019-04-13 15:56:29

2019-04-13 17:02:24

Theis Christian Jensen Ballegaar
2019-04-13 17:03:12

Antonio Robbins
2019-04-13 18:59:40

Rose Stumpwater
2019-04-13 20:04:11

John Bubuz
2019-04-14 06:40:59

原文網址 Antonio Robbins
2019-03-04 06:24:45

Wiggly lines on the side of prints- what's the cause? It's no where else on the model.

I thought it might be fee but it's still tight as a drum head. (How do you know when it needs changed?)

This was an 18 hr print at 0.025 mm.

翻譯年糕

Giuseppe La Capra
2019-03-04 08:13:43

Antonio Robbins
2019-03-04 08:55:16

原文網址 Antonio Robbins
2018-12-27 07:09:04

DC POWER CONNECTION
Odd question I'm sure, but does anyone know of a DC connector that would work on the Photon?

(Either one that plugs into a car lighter outlet or is directly wired to a 12 battery. )

翻譯年糕

Richard Shapiro
2018-12-27 11:05:17

Antonio Robbins
2018-12-27 11:30:32

Antonio Robbins
2018-12-27 11:31:24

Richard Shapiro
2018-12-27 11:41:46

Richard Shapiro
2018-12-27 11:43:46

Antonio Robbins
2018-12-27 11:58:36

Antonio Robbins
2018-12-27 12:54:31

Richard Shapiro
2018-12-27 22:16:38

Gazsó Péter
2018-12-27 22:24:11

Antonio Robbins
2018-12-28 03:01:34

原文網址 Antonio Robbins
2018-12-23 23:22:47

My 10hr print finished and looked well... until I saw it's "bending" due to weight despite being hollow.
How thick are your walls? My 10hr print finished and looked well... until I saw it's "bending" due to weight despite being hollow.
How thick are your walls? 翻譯年糕

Antonio Robbins
2018-12-23 23:26:30

Philippe Maegerman
2018-12-24 00:18:58

Chad Elstad
2018-12-24 00:47:39

Robert Silvers
2018-12-24 00:54:21

Chris Cardinal
2018-12-24 01:23:22

原文網址 Antonio Robbins
2018-12-22 14:32:14

ERROR M_11800

I've gotten this error twice now; is this something indicating a different known or larger issue?
---
It's happened on two different USB drives that work fine otherwise (on small prints.)

After unpluggikg and replugging it back in attempting to continue causes the Photon to lock up and has to be rebooted to start a new print.

GitHub page says an Anycube engineer said "this means USB not plugged in."

First drive was a 4GB, second is an 8GB.

翻譯年糕