Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Jeff Gowers
2019-02-14 09:47:32

Loaded the original Photon Slicing software on my Laptop PC. That part went fine. When I open the program the “build plate” is not shown. It will let me open a model but doesn’t show it on the screen. When I try and select it on the screen of course it says “Please load a valid model”. Any ideas? Thanks.

翻譯年糕

Robert Anhalt
2019-02-14 09:48:52

Sean O'Hayer
2019-02-14 09:52:04

Jeff Gowers
2019-02-14 09:59:18

Jeff Gowers
2019-02-14 09:59:46

Robert Anhalt
2019-02-14 10:24:19

Per Bekker-Madsen
2019-02-14 16:08:26

Robert Mako Sharkey
2019-02-14 19:28:10

Pietro Malaguti Abbate
2019-02-14 19:32:23

Jeff Gowers
2019-02-14 19:33:00

Per Bekker-Madsen
2019-02-14 20:36:06

Per Bekker-Madsen
2019-02-14 20:37:36

Bard Vanhammer
2019-02-15 08:35:40

Peter Horvat
2019-02-16 02:16:31

原文網址 Jeff Gowers
2019-02-13 09:21:55

So third print now with the Anycubic grey resin and they all have failed. I have re-zeroed again and that didn’t help. Any idea what is going on here. Using ChiTuBox also.

翻譯年糕

Trung Mi
2019-02-13 09:30:08

Jeff Gowers
2019-02-13 09:34:55

Brandon Richard
2019-02-13 09:36:33

Dustin Scott
2019-02-13 09:40:02

Jeff Gowers
2019-02-13 09:42:49

Jeff Gowers
2019-02-13 09:43:15

Jeff Gowers
2019-02-13 09:44:11

Brandon Richard
2019-02-13 09:44:13

Jeff Gowers
2019-02-13 09:44:30

Richard Shapiro
2019-02-13 09:46:26

Richard Shapiro
2019-02-13 09:48:20

Jeff Gowers
2019-02-13 09:49:33

Richard Shapiro
2019-02-13 09:50:20

Dustin Scott
2019-02-13 09:54:08

Glenn Mcfadden
2019-02-13 13:05:33

Philipp Maitrot
2019-02-16 00:01:06

Alex Vee
2019-02-16 00:04:10

Tim Biggers
2019-02-16 04:18:24

原文網址 Jeff Gowers
2019-02-11 20:21:51

Printed the test cube yesterday on my new Photon. The inner diagonal with the Photon name did not come out fully. Some of the outer lattice near that cross piece was slightly distorted also.

I did notice when it was printing (and was able to see it when the print plate rose above the vat) that it seemed like it was sticking to the FEP. There would be a slight delay and it looked like the cube was pulling a little. So maybe need to adjust the zero height up 0.1 or 0.2 mm.

Thoughts? Thanks.

翻譯年糕

Dustin Scott
2019-02-11 20:23:17

原文網址 Jeff Gowers
2019-02-07 09:18:59

So newbie question here. Loaded the Anycubic Slicer software (MAC version running High Sierra). I am getting the following error. Anyone have an idea of what is going on? Thanks.

翻譯年糕