Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Elambharathi Manickawasagam
2020-02-19 01:30:34

I broken the reinforced glass on my lcd screen. Is there any solution to replace the glass alone or I have to purchase the entire lcd screen?

翻譯年糕

Zena Andreou
2020-02-19 01:33:50

Elambharathi Manickawasagam
2020-02-19 01:34:48

Zena Andreou
2020-02-19 01:35:22

Elambharathi Manickawasagam
2020-02-19 01:35:50

Elambharathi Manickawasagam
2020-02-19 01:37:28

Zena Andreou
2020-02-19 01:47:31

Paul West
2020-02-19 01:53:14

Elambharathi Manickawasagam
2020-02-19 03:05:11

Ryan Tudor
2020-02-19 03:09:25

Paul West
2020-02-19 03:11:06

Zena Andreou
2020-02-19 03:37:08

原文網址 Elambharathi Manickawasagam
2020-02-07 18:33:37

Hi, I start printing my new model in photon with anycubic skin. After finding failure of the print. I took it out and it look like this. Why the surface is uneven. Uniformity is not made?

翻譯年糕

Jayapal Selvaraj
2020-02-07 18:35:33

Elambharathi Manickawasagam
2020-02-07 18:38:51

Jayapal Selvaraj
2020-02-07 19:13:44

原文網址 Elambharathi Manickawasagam
2019-02-25 20:40:15

After doing some experiments over on resin, i received the below mentioned results.

But, the value not same from top to the bottom. Minimum of 0.1mm taper difference occurs. I conducted a test in 2 different exposure timings.
1. Size of the model not changed, the exposure time is 7secs, offtime 6.5secs, base exposure time is 28secs.

Value i got is +0.12mm from the required value in xy direction and -0.15mm from required in z direction. Taper is 0.02mm from top to bottom.

2. Size scaled for to compensate, exposure time 7 sec, off time 5 sec, base exposure time is 40sec.

Value i got is from -0.04mm at the bottom to +0.04mm at the top from required values.

This because of what?
Till now i am not able to calibrate the black resin for accurate components. Because the components has 0.02mm tolerance.

翻譯年糕

Elambharathi Manickawasagam
2019-02-25 20:41:51

Marcin Kudzia
2019-02-25 20:42:09

Elambharathi Manickawasagam
2019-02-25 20:42:24

Elambharathi Manickawasagam
2019-02-25 20:42:51

Elambharathi Manickawasagam
2019-02-25 20:46:13

Lehe Born
2019-02-25 21:59:16

Giuseppe La Capra
2019-02-25 23:10:26

Elambharathi Manickawasagam
2019-02-26 00:06:48

Giuseppe La Capra
2019-02-26 00:22:09

André Klein
2019-02-26 04:53:34

原文網址 Elambharathi Manickawasagam
2019-02-24 01:38:39

Good evening friends,

I bought anycubic UV black resin, while running resin test, i received the below result (resin test_50u_b100_2_20.photon). I have choosen the exposure time is 7 sec (in between of 3rd and 4th column). But, while printing Go Nogo gauge, i received +0.1mm in xy and -0.15mm in z directions. Go pin with 0.3 only enters. Help me to find, where i am wrong?

翻譯年糕