Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Todd Jones
2019-07-20 04:09:21

Brand new motherboard and LCD. Anyone seen this?

翻譯年糕

Richard Flanagan
2019-07-20 04:13:45

Todd Jones
2019-07-20 04:20:26

Gavin Paull
2019-07-20 04:25:53

Todd Jones
2019-07-20 04:30:57

Todd Jones
2019-07-20 04:32:36

Simon Jackson
2019-07-20 05:46:40

Todd Jones
2019-07-20 06:15:14

Patrick Smith
2019-07-20 06:35:20

Simon Jackson
2019-07-20 07:06:27

James Cachia-Garrett
2019-07-20 11:59:47

Adam Sibille
2019-07-20 13:19:08

Adam Sibille
2019-07-20 13:19:42

Todd Jones
2019-07-20 13:50:23

Todd Jones
2019-07-20 13:52:16

Todd Jones
2019-07-20 13:53:49

原文網址 Todd Jones
2019-06-22 08:12:18

I'm guessing the servo is done. Can turn shaft by hand.

翻譯年糕

Todd Jones
2019-06-22 11:36:34

Andy Tidball
2019-06-22 16:05:25

Juan Carlos Ramirez
2019-06-23 00:27:06

Andy Tidball
2019-06-23 00:53:28

Eric Jorgensen
2019-06-23 01:03:39

Todd Jones
2019-06-23 01:14:43

Juan Carlos Ramirez
2019-06-23 01:44:26

Juan Carlos Ramirez
2019-06-23 01:45:57

Juan Carlos Ramirez
2019-06-23 01:47:30

Andrey Sabrev
2019-06-23 01:50:17

Todd Jones
2019-06-23 07:57:52

Juan Carlos Ramirez
2019-06-23 08:00:26

Todd Jones
2019-06-23 08:03:24

Juan Carlos Ramirez
2019-06-23 08:28:51

Juan Carlos Ramirez
2019-06-23 08:30:47

Juan Carlos Ramirez
2019-06-23 08:35:20

Peter Lynn
2019-06-23 08:37:02

Juan Carlos Ramirez
2019-06-23 08:38:03

Juan Carlos Ramirez
2019-06-23 08:38:07

Juan Carlos Ramirez
2019-06-23 08:38:11

Juan Carlos Ramirez
2019-06-23 08:38:41

Juan Carlos Ramirez
2019-06-23 08:40:55

Juan Carlos Ramirez
2019-06-23 08:41:45

Juan Carlos Ramirez
2019-06-23 08:45:47

Todd Jones
2019-06-23 08:53:21

Eric Jorgensen
2019-06-23 08:59:01

Todd Jones
2019-06-23 09:01:30

Juan Carlos Ramirez
2019-06-23 09:22:27

Andrey Sabrev
2019-06-23 13:53:00

原文網址 Todd Jones
2019-06-07 10:35:12

Has anyone had the LED array go bad? I ask as one of my printers is continually failing where the supports attach to the part. I can run the exact same print/settings (the same USB to be clear) on another photon and it works fine so the LED is the only thing I can think of. It's not a leveling issue as it adheres to the build plate fine. I also swapped the vat and no difference.

I cranked up the exposure a few seconds (More than the other photons need with same exact file and resin) and it helped but still had some support failures.

I did just change out the LCD in this printer but not seeing any issues there.

Ideas?

翻譯年糕

Elvin Torok
2019-06-07 10:41:56

Todd Jones
2019-06-07 10:43:58

Todd Jones
2019-06-07 10:45:08

Stefan Giudici
2019-06-07 10:53:33

Todd Jones
2019-06-07 10:57:43

Andy Eakin
2019-06-07 10:59:19

Todd Jones
2019-06-07 11:06:17

Pekka Haarala
2019-06-07 12:40:50

Danny Lloyd
2019-06-07 15:50:18

原文網址 Todd Jones
2019-06-01 04:39:23

Is there a file size limit with the Validator or is it computer related? I've been trying to load a 176mb file and it just sits there "loading file" while a 34mb file loaded right off.

翻譯年糕

原文網址 Todd Jones
2019-02-27 05:57:05

After a week I've already about used up the 500ml of Elegoo grey I bought with the printer. Fairly happy with it to this point but would like to know how it compares with Anycubic Black. Or, what is the best resin for high detail? My parts have some very small features that need to be sharply rendered so I'm looking for the best I can get at a reasonable price.
7

翻譯年糕

Chris D'Andrea
2019-02-27 06:24:28

Todd Jones
2019-02-27 06:27:24

Todd Jones
2019-02-27 06:28:57

Chris D'Andrea
2019-02-27 06:29:35

Richard Cooper
2019-02-27 12:35:11

Brayden Funk
2019-02-27 12:50:20

Todd Jones
2019-02-28 12:12:22

Richard Cooper
2019-02-28 13:24:41

原文網址 Todd Jones
2019-02-24 08:28:29

I'm having an issue with "lines" on the last couple of runs of parts. The odd thing is the lines are only on the parts on one side of the build platform. Here are two of the parts, both from the same run.

The one with the lines was on the left side of the build plate. Without lines on the right. Both printed with same orientation/upside down. The lines are vertical and only on the vertical faces. Interestingly, another part from the left side has lines that are spaced wider than shown here. This seems very odd, but I'm guessing it's a know issue to those here?

翻譯年糕