• COSPLAY 3D 建模
  • 3D列印服務
  • #maker+t=market
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Mike Tree
2019-05-07 20:44:11

On a scale of Elegoo to Anycubic, how smelly is Monocure? On a scale of Elegoo to Anycubic, how smelly is Monocure? 翻譯年糕

Brandon Richard
2019-05-07 20:45:30

Sen Kun
2019-05-07 21:36:48

Rasmus Josephsen
2019-05-07 22:11:23

Rasmus Josephsen
2019-05-07 22:11:32

Alwin Chan
2019-05-07 22:47:05

John Fulmer
2019-05-07 22:54:48

Chris Kaczmarczyk
2019-05-08 01:10:48

Kevin Rank
2019-05-08 01:24:35

David Nicholls
2019-05-08 02:15:18

Nick Eichler
2019-05-08 05:53:31

Kieran Birchley
2019-05-08 12:05:37


原文網址 Mike Tree
2019-05-07 01:46:40

I printed mz4250 goblin & painted it. I then took a photo to upload which shows the layer lines. I can't actually see them with the naked eye.

翻譯年糕

Nate Nelson
2019-05-07 01:54:59

Mike Tree
2019-05-07 04:44:22


原文網址 Mike Tree
2019-05-07 01:42:44

Tip of the day. BEFORE removing your print from the print bed, take several sheets off your kitchen roll. It is easier without resin covered gloves.

翻譯年糕

Paul Mabbott
2019-05-07 01:45:11

Jarrod Smith
2019-05-07 01:48:24

Mike Michaels
2019-05-07 02:03:49

Stuart Presley
2019-05-07 02:09:43

Dennis Back
2019-05-07 02:16:14

Nick Porterfield
2019-05-07 02:39:35

Dennis Back
2019-05-07 03:18:51

Nick Porterfield
2019-05-07 03:20:00


原文網址 Mike Tree
2019-05-04 18:11:21

I’ve been using elegoo clear and it is really low odour. Is the elegoo black similar? I’ve been using elegoo clear and it is really low odour. Is the elegoo black similar? 翻譯年糕

Philipp Maitrot
2019-05-04 18:25:18

Mike Tree
2019-05-04 19:50:07


原文網址 Mike Tree
2019-05-04 04:38:34

I’ve had some great prints but often get this issue. Elegoo clear. 17s xp. 0.1 layer height

翻譯年糕

Bob Deblier
2019-05-04 15:23:42

Mike Tree
2019-05-04 18:11:54


原文網址 Mike Tree
2019-05-02 21:39:13

Has anyone considered using the photon’s UV for post print curing? Remove the vat and run a G-code to turn lamp on. Has anyone considered using the photon’s UV for post print curing? Remove the vat and run a G-code to turn lamp on. 翻譯年糕

伟洪
2019-05-02 21:39:47

Chayanin Somton
2019-05-02 21:40:14

Gary Houser
2019-05-02 22:09:39

Mike Tree
2019-05-02 23:09:18

Patrick Nixon
2019-05-02 23:28:22

Mike Tree
2019-05-02 23:45:41

Nas Syed
2019-05-03 00:00:40

William David Cunningham
2019-05-03 05:49:02

Scott Clark
2019-05-03 05:59:04

Scott Clark
2019-05-03 06:00:50

Jesse Stenner
2019-05-03 06:32:05

Nick Williams
2019-05-03 08:31:50

Jesse Stenner
2019-05-03 08:39:50

Dexter WG
2019-05-03 15:30:12


原文網址 Mike Tree
2019-05-02 06:34:46

I have a UV nail lamp. How long do I need to cure prints? I have read times varying from a few minutes to a few hours. Does it vary? if so, what are the factors I need to calculate the time required? Currently using Anycubic green & Elegoo clear

翻譯年糕

Brad Dudenhoffer
2019-05-02 10:36:36

Brad Dudenhoffer
2019-05-02 12:52:58


原文網址 Mike Tree
2019-04-28 03:21:29

I just shook my new bottle of ELEGOO (as instructed) & poured some into the vat. It has a lot of bubbles. Do I need to wait until they disappear before printing?

翻譯年糕

Tori Beckett
2019-04-28 03:28:54

Mike Tree
2019-04-28 03:30:24

Chris Visser
2019-04-28 03:40:38

Mike Tree
2019-04-28 03:47:22

Chris Comeau
2019-04-28 04:52:06

Niklas Landin
2019-04-29 02:57:35


原文網址 Mike Tree
2019-04-28 03:19:03

After a couple of successful prints I just had a failure. I don't mind that, but while removing resin stuck to the FEP I appear to have made a hole. I think it may have been a small dot of resin stuck to the FEP that pulled a hole. Anyway It didn't take too long to change it. Better get some more spare FEPs :(

翻譯年糕


原文網址 Mike Tree
2019-04-27 06:35:59

My first print, with a coat of primer to highlight the detail. Very happy with the result.

翻譯年糕


 

討論主題

全不選 常用關鍵字