Hey everyone, I've had my Photon S for a little over a week now, and I've had a lot of successful prints, but I feel like the quality of my prints seems very low compared to what I see here.
I feel like I've tried everything, but I just can't get the print to look better, and I really hope that I can get some expert advice here.
Here's a small list of things I've "done" to ensure quality.
Leveled build plate 3 times to ensure it's level and close to the LCD.
I normally shake resin properly, but I've also tried not shaking it.
I've printed models "upright" and at 45 degrees (45 deg helped a miniscule amount)
Tried 0.02, 0.04 and 0.05mm height.
Tried both Anycubic Green and Anycubic Aqua Blue resins.
Tried with more and less support.
Cleaned and inspected FEP
Cleaned FEP and LCD
I ALWAYS clean my models in 2 different IPA baths and always cure them for 20+ minutes under UV.
I've been painting Warhammer etc. for a number of years, it's not a paint primer issue
:(
I'm out of ideas of what could be the problem, I've attached a picture of one of the best "28mm" scale (30mm tall from head to toe) that I've managed to print (it's been primed)
翻譯年糕
Stefan Giudici
2019-07-28 05:51:08
Nico Sand
2019-07-28 05:53:15
Thomas Wright
2019-07-28 05:54:25
Stephen Parac
2019-07-28 05:55:41
Nico Sand
2019-07-28 05:57:24
Joshua Collins
2019-07-28 05:58:30
Thomas Wright
2019-07-28 06:01:19
Shivanand Chanderbally
2019-07-28 06:08:44
Nico Sand
2019-07-28 06:11:27
Mike Fatchett
2019-07-28 06:11:34
Gabrielle Underhill Lucas
2019-07-28 06:12:26
Nico Sand
2019-07-28 06:13:48
Gabrielle Underhill Lucas
2019-07-28 06:15:36
Gabrielle Underhill Lucas
2019-07-28 06:16:44
Kory Sebby
2019-07-28 06:19:50
Nico Sand
2019-07-28 06:20:34
Nico Sand
2019-07-28 06:22:25
Mark Wardle
2019-07-28 06:24:39
Charles Mercieca
2019-07-28 06:25:14
Stefan Giudici
2019-07-28 06:25:23
Nico Sand
2019-07-28 06:26:39
Nico Sand
2019-07-28 06:26:57
Scott Pavlich
2019-07-28 06:29:28
Nico Sand
2019-07-28 06:29:54
Nico Sand
2019-07-28 06:30:20
Mark Wardle
2019-07-28 06:30:39
Scott Pavlich
2019-07-28 06:31:08
Nico Sand
2019-07-28 06:31:16
Nico Sand
2019-07-28 06:32:00
Mark Wardle
2019-07-28 06:32:03
Nico Sand
2019-07-28 06:32:54
Nico Sand
2019-07-28 06:33:58
Mark Wardle
2019-07-28 06:34:14
Scott Pavlich
2019-07-28 06:41:53
Scott Pavlich
2019-07-28 06:42:32
Nico Sand
2019-07-28 06:45:37
Scott Pavlich
2019-07-28 06:47:42
Mark Wardle
2019-07-28 06:50:27
Gabrielle Underhill Lucas
2019-07-28 06:54:28
Thomas Wright
2019-07-28 06:55:50
Nico Sand
2019-07-28 06:56:21
Rob McEwen
2019-07-28 06:57:37
Gilles Miguel
2019-07-28 07:06:25
Jon Carroll
2019-07-28 07:16:29
David Nicholls
2019-07-28 07:20:51
Kallon Fernandez-Tripp
2019-07-28 07:22:19
Chad Elstad
2019-07-28 07:23:03
Gustaf Sjögren
2019-07-28 07:25:01
Chris Graf
2019-07-28 07:52:04
Wayne Rogers
2019-07-28 08:57:17
Jon Carroll
2019-07-28 09:57:41
Susan Sioux Mercer
2019-07-28 10:20:19
Chad Elstad
2019-07-28 10:20:44
Jared Zadorozny
2019-07-28 10:53:38
Minghua Kao
2019-07-28 16:11:49
Nico Sand
2019-07-28 16:20:52
Nico Sand
2019-07-28 16:22:49
Susan Sioux Mercer
2019-07-28 16:42:22
Nico Sand
2019-07-28 16:43:03
David Nicholls
2019-07-28 17:30:12
Nico Sand
2019-07-28 17:31:40
Nico Sand
2019-07-28 20:33:10
Richard Humble
2019-07-28 21:18:01
Stefan Giudici
2019-07-28 22:15:32
Anthony Walker
2019-07-29 08:58:02
Susan Sioux Mercer
2019-07-29 08:59:27
Thomas Wright
2019-08-01 06:46:12
Nico Sand
2019-08-01 08:00:43
