Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Tom Hope
2019-12-11 01:46:56

Got the Lithophanes to print properly and have 3 going right now for various family members. The longest part is printing the box I designed for them to live in ?

I wasn't sure how much light I would need and got 3 different LEDs to test with and thankfully the first and only one that can run off regular USB worked. Was worried I would need to use a slightly more powerful one that would require a wall wart

翻譯年糕

Garph Johns
2019-12-11 01:54:12

Tom Hope
2019-12-11 01:57:29

Tom Hope
2019-12-11 01:59:29

Garph Johns
2019-12-11 02:17:13

Tom Hope
2019-12-11 02:23:02

Garph Johns
2019-12-11 02:30:06

Brett Isaacs
2019-12-11 03:22:16

Brett Isaacs
2019-12-11 03:22:36

Brett Isaacs
2019-12-11 03:22:53

Ben Bicakci
2019-12-11 08:37:07

Brett Isaacs
2019-12-11 09:36:28

Tom Hope
2019-12-11 10:50:13

Jan Pfriender
2019-12-12 02:18:36

Tom Hope
2019-12-12 08:54:37

Jan Pfriender
2019-12-12 09:34:22

Tom Hope
2019-12-12 09:40:18

原文網址 Tom Hope
2019-11-27 00:30:13

If at first you don't succeed... Try try again ?

One had a very interesting failure ?

翻譯年糕

Joe Cahill
2019-11-27 00:50:06

Tom Hope
2019-11-27 00:54:26

原文網址 Tom Hope
2019-11-22 17:58:19

Does anyone have any tips for printing lithophanes? I've been trying for a while to make a gift for my Great Aunt but this always happens. At least 1 edge will detach from the plate and result in a failure ultimately. My guess is there just isn't enough contact to the plate to hang on and gradually pulls away, so the fix would be to increase that surface area... but I'm not sure the best way to implement that. All my other prints have been perfect with the same settings, even printed a Baby Yoda in the same vat of resin with the same settings... ?‍♂️

I experimented with using supports but that didn't work cause it seemed to introduce a lot of wobble which created layer shifts. I did get a full print when I angled it, but that was also failure. The only info about resin lithophanes I could find was a FormLabs piece and I was already doing everything advised there haha.

Resin is Monocure Rapid Cure in the Photon S. Thanks in advance for any tips / advice ?

翻譯年糕

Sjefke Poulussen
2019-11-22 18:07:35

Tom Hope
2019-11-22 18:08:49

Bob Deblier
2019-11-22 18:45:42

Itse Kuiper
2019-11-22 19:00:19

Rafel Lin
2019-11-22 19:04:50

Oliver Matthews
2019-11-22 19:06:31

Zäta Doe
2019-11-22 19:11:14

George Bulte
2019-11-22 19:23:39

Joe Muecke
2019-11-22 20:04:50

Joe Muecke
2019-11-22 20:05:30

Nigel White
2019-11-22 20:47:48

Paul West
2019-11-22 23:43:10

Tom Hope
2019-11-22 23:56:22

Scott Pavlich
2019-11-23 01:27:01

Zäta Doe
2019-11-23 07:09:12

Joe Muecke
2019-11-24 00:11:24

原文網址 Tom Hope
2019-08-31 04:52:26

I am getting my Photon S today and was wondering if anyone is using OctoPrint with their printer. I know it can print offline, but I am amazingly lazy and having to plug a USB stick into the printer every time I wanna print just seems like too much work (first world problem right?).

So I was wondering if OctoPrint will be fine or if there are issues with running it and if so is there is something else that can be used. Not a requirement but it would be a nice to have ?

翻譯年糕

阮天青
2019-08-31 04:58:14