Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 David N. Amis
2020-03-13 10:26:20

I moved recently and turned my printer on. Now, I can't level the bed, and I'm getting a z= zero is decided by the trigger position message. I cannot level the bed whatsoever. What am I missing?

翻譯年糕

Pete Kastner
2020-03-13 10:31:40

David N. Amis
2020-03-13 10:36:47

Pete Kastner
2020-03-13 10:40:18

David N. Amis
2020-03-13 10:41:16

Stefan Giudici
2020-03-13 10:41:49

David N. Amis
2020-03-13 10:42:01

Stefan Giudici
2020-03-13 10:42:07

David N. Amis
2020-03-13 10:42:19

David N. Amis
2020-03-13 11:09:19

Nick Eason
2020-03-13 15:46:18

David N. Amis
2020-03-13 19:21:25

David N. Amis
2020-03-13 19:30:01

Nick Eason
2020-03-14 00:25:05

David N. Amis
2020-03-14 00:25:39

原文網址 David N. Amis
2019-10-29 10:56:45

Here's to hoping I've got it dialed in for the rest

翻譯年糕

原文網址 David N. Amis
2019-10-27 11:21:21

Intended print and setting, not hollow. Attempted once so far, and only the base layer appeared stuck to the FEP. Any ideas? Using anycubic green with some elegoo grey accidentally mixed in....that was a strange mistake to make while inebriated.

翻譯年糕

Lee Baxter
2019-10-27 11:24:40

Lee Baxter
2019-10-27 11:25:17

Lee Baxter
2019-10-27 11:25:47

David N. Amis
2019-10-27 11:26:23

Lee Baxter
2019-10-27 11:27:23

David N. Amis
2019-10-27 11:28:17

Lee Baxter
2019-10-27 11:28:56

David N. Amis
2019-10-27 11:29:18

David N. Amis
2019-10-27 11:29:50

Lee Baxter
2019-10-27 11:30:23

原文網址 David N. Amis
2019-10-20 01:04:54

Just to see if I'm getting this right...after running the file through the prusaslicer for auto-supports, then do you guys run the file through chitubox for manual supports elsewhere? I haven't played with the prusaslicer much, but the auto-supports seem a little thick as well.

翻譯年糕

Paul West
2019-10-20 01:07:01

Tom Inglis
2019-10-20 15:54:55

原文網址 David N. Amis
2019-10-16 06:30:54

If I wanted to combine all of these pieces for easier printing, how could I go about that?

翻譯年糕

Greg Chapman
2019-10-16 06:44:27

Ben Bequer
2019-10-16 06:47:50

Dane Bennett
2019-10-16 06:47:52

David N. Amis
2019-10-16 06:48:17

Ben Bequer
2019-10-16 06:48:56

Andrej Stojsin
2019-10-16 07:41:15

Steven Howland
2019-10-17 10:55:37

Nathan Inwin
2019-10-17 16:01:30

Nathan Inwin
2019-10-17 16:04:38

Andrey Kulkov
2019-10-17 16:11:18

Luke Mason
2019-10-18 18:11:14

原文網址 David N. Amis
2019-10-16 02:52:27

If I wanted to print this hollow, but didn't want to have to make holes in each individual tooth, is there a way to avoid that?

翻譯年糕

Jake Bradbury
2019-10-16 02:54:48

David N. Amis
2019-10-16 02:56:25

Chasen Harris
2019-10-16 03:09:33

David N. Amis
2019-10-16 03:09:50

Chasen Harris
2019-10-16 03:10:23

Chasen Harris
2019-10-16 03:10:59

Jake Bradbury
2019-10-16 03:11:18

David N. Amis
2019-10-16 03:14:35

Chasen Harris
2019-10-16 03:33:08

原文網址 David N. Amis
2019-10-01 23:27:36

So, just got my Photon, and I started with some weird results.

Got the bed leveled to my satisfaction, and started the test cube. Here's what I got. Could it be that the resin in the vat wasn't distributed evenly? The table is a little uneven.

Thank you for any insight!

翻譯年糕