• 3D列印服務
  • #maker+t=market
  • COSPLAY 3D 建模
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Jai Pate
2019-12-05 05:51:04

So I did a quick print and used a rattle can primer + paint like ten days ago. The thing is in a climate controlled part of the house so it’s 68-70 degrees but the paint is still tacky. I used grey elegoo and cured it (maybe extra cured) and let it sit for two or three days before I sprayed it. Any ideas?

翻譯年糕

Randy Shepherd
2019-12-05 05:53:49

Jai Pate
2019-12-05 05:54:45

Randy Shepherd
2019-12-05 05:55:58

Alexander Keith
2019-12-05 05:57:04

Jai Pate
2019-12-05 05:57:20

Jarin Udom
2019-12-05 06:00:36

Jim Nelson
2019-12-05 06:00:54


原文網址 Jai Pate
2019-11-11 09:12:58

Just rinsed and pulled supports. Not sure what’s up with the warp.

翻譯年糕


原文網址 Jai Pate
2019-11-03 23:22:24

A couple of prints yesterday. Cigar tube (background) and cap and the MIZZOU columns. A couple of questions: when adding resin mid-print are you guys pausing it or just opening and pouring? With the colorless resin, to avoid yellowing, any suggestions on making sure I get a good cure? I just eyeballed it after a couple of minutes and things are fine, just curious as to what everyone else is doing.

翻譯年糕

Zac Linhart
2019-11-03 23:38:20

Jai Pate
2019-11-03 23:44:43

Aaron Wiggins
2019-11-04 00:05:56

Jai Pate
2019-11-04 01:46:50

Zac Linhart
2019-11-04 02:23:38

Travis K. Jansen
2019-11-04 03:17:43

Travis K. Jansen
2019-11-04 03:32:05

Zac Linhart
2019-11-04 03:43:30

Zac Linhart
2019-11-04 03:50:03

Jai Pate
2019-11-04 04:48:27

Zac Linhart
2019-11-04 08:10:02

Travis K. Jansen
2019-11-04 10:55:16


原文網址 Jai Pate
2019-10-29 07:36:57

Okay friends, I am looking for someone who can design something for me. I am a disabled vet and was hoping to make some things for some of the guys I served with, but cant find a file for what I need. If anyone is up to the challenge PM me.

翻譯年糕

Stoica Ioan
2019-10-29 07:39:09

Jai Pate
2019-10-29 08:24:14

Yanki Kanarya
2019-10-29 21:57:41

Stoica Ioan
2019-10-30 06:49:23

Jai Pate
2019-10-30 07:40:26

Jai Pate
2019-10-30 07:41:13

Stoica Ioan
2019-10-30 10:45:45

Jai Pate
2019-10-30 10:53:25


原文網址 Jai Pate
2019-10-15 21:47:20

I’m waiting in my new motherboard to arrive from China. Y’all’s pictures have got me sitting here like Pavlov’s dog.

翻譯年糕

Jimmy Louis
2019-10-15 21:58:26

Gary Houser
2019-10-15 22:25:36


原文網址 Jai Pate
2019-10-08 08:45:07

Has anyone fried their motherboard? How hard is it to replace the tiny ribbon cable in the center of the board?

翻譯年糕

Andrew Good
2019-10-08 09:13:43


原文網址 Jai Pate
2019-10-03 23:44:08

Hello everyone. I’m brand spanking new to the hobby. My printer did not have the test print installed in the thumb drive so I dove right in. My first print was an attempt at the Eiffel Tower. Two feet didn’t stick to the build plate so I stopped it about halfway through. I tried supporting it, but nothing printed except the supports. Last night I switched it up and tried Notre Dame, the bottom printed, but not the top. I am thinking about increasing layer time and inverting the model and adding supports. I have successfully printed a nut and bolt. Any other ideas? Has anyone else run into this/these problems? I’ve leveled and releveled. I have cleaned and recleaned the FEP and LCD. I did increase layer time for first layers and increased the number of first layers. It seems like it’s the details that don’t want to print.

翻譯年糕

James Roberts
2019-10-03 23:46:38

Damo Cramp
2019-10-04 00:31:48

Jai Pate
2019-10-04 00:33:09

Jai Pate
2019-10-04 00:33:41

James Roberts
2019-10-04 00:49:57

Damo Cramp
2019-10-04 00:52:34

James Roberts
2019-10-04 04:12:02


 

討論主題

全不選 常用關鍵字