Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Thomas Kenneth Scheer
2019-12-28 05:36:49

Photon s all firmware updated. Using correct usb . Done many prints.
New problem. Printer locks up during print several times. I must shut off printer, wait 30 seconds and the restart it. Clean off build plate then resart print . Several prints then freezes again. The problem of freezing without me doing anything is getting more abundant.. any suggestions and have you had this problem.

翻譯年糕

Alexander Bayerdorffer
2019-12-28 05:52:30

Thomas Kenneth Scheer
2019-12-28 06:52:46

Nick Robinson
2019-12-28 07:12:11

原文網址 Thomas Kenneth Scheer
2019-12-18 04:14:55

https://m.facebook.com/story.php?story_fbid=10157799293729183&id=792329182

James Woods
2019-12-18 04:16:51

Ian Henry
2019-12-18 04:22:04

Ian Henry
2019-12-18 04:22:50

Thomas Kenneth Scheer
2019-12-18 04:27:27

Francis Lapointe
2019-12-18 04:28:56

Ekaterina Vitalyevna
2019-12-18 04:37:18

Chris D'Andrea
2019-12-18 04:47:56

Carter Goforth
2019-12-18 04:49:16

Joe Broggio
2019-12-18 04:53:58

Ian Henry
2019-12-18 04:58:40

Darren Donovan
2019-12-18 05:28:20

RIcardo Castillo
2019-12-18 05:33:45

Mark Rhodes
2019-12-18 06:41:32

Serin Jameson
2019-12-18 07:09:52

Serin Jameson
2019-12-18 07:10:12

Olivier Aidouni
2019-12-18 07:29:49

Elle Heilig
2019-12-18 08:26:58

Orlando Lopez
2019-12-18 11:48:46

Johnny Johnsen
2019-12-18 11:59:03

Jeff Greenfield
2019-12-18 12:19:48

Victor Cabral Ferreira
2019-12-18 19:07:43

John Klingbeil
2019-12-19 01:45:53

João Batista Pereira
2019-12-19 03:25:14

Jimmy Louis
2019-12-19 23:39:47

Randy Hayes
2019-12-20 01:22:09

原文網址 Thomas Kenneth Scheer
2019-12-15 09:03:19

Had a failed print but still using it for my son.

翻譯年糕

Kayo Michiels
2019-12-16 03:52:50

原文網址 Thomas Kenneth Scheer
2019-12-13 05:59:20

https://www.facebook.com/ANYCUBIC3dprinter/videos/2409661089297764/

Vernie G-graphy
2019-12-13 06:50:42

原文網址 Thomas Kenneth Scheer
2019-11-16 07:49:44

Anyone have a photon S vent system setup they would like to share details? Anyone have a photon S vent system setup they would like to share details? 翻譯年糕

Richard Webb
2019-11-16 07:56:23

Kārlis Dii Lers Dišlers
2019-11-16 08:39:05

原文網址 Thomas Kenneth Scheer
2019-11-08 05:10:21

After 30 some fails, wasted bottles of any cubic resin switched to eelgoo grey finally the test print came perfectly but vs 5.00 firmware on photon s. Also upcycled the resin box. Yes my off time is 6 made the print straight

翻譯年糕

原文網址 Thomas Kenneth Scheer
2019-10-27 00:38:39

Here is a link that I found on several discussions that you guys have had but is what I needed posting pictures also of my resin test and my new agitator compressor... my resin test seems to indicate #4 as a overall pick, but since im new i humbly ask of your opinions.. it works only for the upgraded photon S.
https://youtu.be/5-Tvj0tVU4E

翻譯年糕

原文網址 Thomas Kenneth Scheer
2019-10-21 04:34:07

No matter what, usb, with or without supporting, sizing difference, or placement on plate; the test print still fails in the exact same spots. My other print are relatively 95% perfect.. going to switch to green resin. I have tried both anycubic slicer and chitubox with the same failure..

翻譯年糕