Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Roy Escherich
2020-01-05 07:09:31

Hi there! Are there any overall recommendations with regards to cleaning your prints afterwards. I found. Lot of contrary articles.
I am using a ultrasonic cleaner and ipa. The last prints I cleaned came out differently after uv curing. Some where more shiny and some more mat. Not hundred percent sure what makes the difference.

翻譯年糕

Alex Vee
2020-01-05 07:10:40

John Chrapkowski
2020-01-05 07:39:51

Roy Escherich
2020-01-05 07:56:39

Megan Wylie
2020-01-05 08:16:18

John Chrapkowski
2020-01-05 08:26:54

John Chrapkowski
2020-01-05 08:26:59

原文網址 Roy Escherich
2020-01-04 04:06:14

Hi! Is there an option to get a mat / dull surface with the anycubic white resin instead of a glossy one?

翻譯年糕

Mohammad Abbas
2020-01-04 04:15:15

原文網址 Roy Escherich
2020-01-04 01:07:32

I had the problem of my build plate not getting tight enough. After I took apart everything I realized that the little silver ball and the blue nut on the right side did not have enough friction so I sanded both parts with 120 paper. Now everything is tight and I can finally start leveling my bed. Maybe this is helpful to somebody else who is also struggling with tightening the build plate.

翻譯年糕

Jakob Marasch
2020-01-04 01:21:39

原文網址 Roy Escherich
2020-01-03 08:11:25

Hi! I can’t tighten my build plate so that it doesn’t move anymore it doesn’t tilt but I can rotate it although all srews are tightened very well. I already disassembled the hole build plate but can’t find the problem. Any suggestions?

翻譯年糕

Jarin Udom
2020-01-03 08:13:23

Roy Escherich
2020-01-03 08:14:07

Shane Johnson
2020-01-03 08:14:45

原文網址 Roy Escherich
2020-01-02 20:03:21

How long do you normally post cure your prints?

翻譯年糕

Daniel Särnblom
2020-01-02 20:04:40

Zena Andreou
2020-01-02 20:05:45

Roy Escherich
2020-01-02 20:06:51

Victoria L. Cordone
2020-01-02 20:08:50

Derek Reihe
2020-01-02 20:12:58

Roy Escherich
2020-01-02 20:13:19

Gabe Snooks
2020-01-02 20:20:25

Michael Power
2020-01-02 20:24:07

Joe Eckert
2020-01-02 22:03:53

Ryan Tudor
2020-01-02 22:19:33

Roy Escherich
2020-01-02 22:20:28

Rasmus Bremholm
2020-01-02 23:04:43

Chad Elstad
2020-01-02 23:20:48

Roy Escherich
2020-01-02 23:39:25

Luiz Junior
2020-01-02 23:44:20

Keith Yinger
2020-01-03 00:58:05

Timothy Conaway
2020-01-03 01:04:55

Neil Ramsay
2020-01-03 01:29:08

Luiz Junior
2020-01-03 02:27:45

Michael Steadham
2020-01-03 02:54:59

Jarrett Lee
2020-01-03 05:00:35

Christopher Carfi
2020-01-03 05:07:16

Çağrı Aydoğan
2020-01-03 05:41:29

Keith Yinger
2020-01-03 05:43:43

Peter Csaki
2020-01-04 01:15:03

原文網址 Roy Escherich
2020-01-02 05:52:20

Hi. Just received my new photon S and successfully printed the test cube in translucent green. Unalloyed ordered the white and grey anycubic resin. Any recommendations with regards to exposure time for first and other layers? There are many different times out there ranging from 8-15 sec. Thanks in advance !

翻譯年糕

Gon Garcia
2020-01-02 05:56:16