Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Dan Gump
2020-01-24 04:32:16

What generally causes this? Do I just not have enough supports at the front?

翻譯年糕

Johnny Grant
2020-01-24 04:35:56

Dan Gump
2020-01-24 04:38:31

Joey Smith
2020-01-24 04:39:07

Dan Gump
2020-01-24 04:43:52

Johnny Grant
2020-01-24 04:52:20

Johnny Grant
2020-01-24 04:54:51

Evan Boone
2020-01-24 04:55:05

Tom Logan
2020-01-24 07:51:46

Elle Heilig
2020-01-24 09:01:55

Dan Gump
2020-01-24 09:32:42

Michael Harvey
2020-01-25 05:07:04

原文網址 Dan Gump
2020-01-22 09:22:46

Hi, getting a bit frustrated here. This is what my last few prints have looked like after moderate success. Seems like the fist layer or so of the supports prints and then nothing else. Any ideas? I’ve only had this thing for about 2 weeks.

翻譯年糕

Kris Leon
2020-01-22 09:27:22

Dan Gump
2020-01-22 09:44:38

Robert Nisson
2020-01-22 09:45:33

Otto Rey
2020-01-22 10:27:23

Nipuna Gunarathne
2020-01-23 18:31:58

原文網址 Dan Gump
2020-01-22 06:16:20

Has anyone used that Badger airbrush primer that is supposed to be formulated specifically for 3d printing?

翻譯年糕

Craig Rankin
2020-01-22 06:34:34

Dan Gump
2020-01-22 06:35:02

Noah Haskell
2020-01-22 06:41:19

Dan Gump
2020-01-22 06:47:14

Noah Haskell
2020-01-22 06:48:27

Craig Rankin
2020-01-22 06:52:52

原文網址 Dan Gump
2020-01-20 21:36:57

Hi, if I have something that is warped. Would I cure it before or after I use the heat gun on it?

翻譯年糕

Mark Reynolds
2020-01-20 21:37:53

Mikko Meriläinen
2020-01-20 21:38:55

Noah Haskell
2020-01-20 21:50:13

原文網址 Dan Gump
2020-01-20 01:23:37

Hi, here are my settings for Chitubox. I have a Anycubic Photon printer. Can you tell me if these settings look right? My prints are taking at least twice as long as I expect them to take.

翻譯年糕

Penn Davies
2020-01-20 02:35:49

Pierre Eichel
2020-01-20 04:17:13

Dan Gump
2020-01-20 04:20:52

Pierre Eichel
2020-01-20 13:18:30

Bob Deblier
2020-01-21 00:49:58

原文網址 Dan Gump
2020-01-19 12:12:38

Hi, two questions this evening.

#1. What typically causes this (see image)?
#2. Do prints sliced with Chitubox take longer to print than sliced with the Anycubic software? Seems this is the case for me. My prints are turning out pretty good but seem to be taking like twice as long.

翻譯年糕

Zak Williams
2020-01-19 12:22:10

Dan Gump
2020-01-19 12:28:43

Scott Schwoppe
2020-01-20 12:19:29

原文網址 Dan Gump
2020-01-18 02:38:43

After my issues this morning with my photon not printing does it hurt anything to try starting a print without the FEP in the printer?

翻譯年糕

Ryan Tupper
2020-01-18 02:42:02

Herman Simpson
2020-01-18 02:43:18

James Swan
2020-01-18 02:43:54

Alexander Bayerdorffer
2020-01-18 02:45:19

Dan Gump
2020-01-18 02:47:35

Dan Gump
2020-01-18 02:48:07

Dan Gump
2020-01-18 02:57:24

Alexander Bayerdorffer
2020-01-18 03:08:35

James Swan
2020-01-18 04:22:10

Niall Forrester
2020-01-18 08:46:59

原文網址 Dan Gump
2020-01-17 19:55:51

Hi. Issue this morning and am hoping someone can help.

Yesterday printed fine. Woke up this morning, took a print off the build plate and started a new one. As build plate went into the resin, there was a clunk sound and it started buzzing. Print is stuck at 1% for a few minutes. Nothing showing up on the screen to indicate the first layer is running. I wait a couple of minutes and decide to cancel print. Tried to move the build plate up and it buzzes every time that it is supposed to be moving. So like if I hit move up 10mm 3x it will buzz pause and buzz again.

Turned printer off and on again and when I try to raise up the build plate still buzzing every time I press the button. Has anyone had this issue before? Any way to raise up the build plate manually?

翻譯年糕

Sander van Deijl
2020-01-17 20:01:17

Dan Gump
2020-01-17 20:04:45

Jens Verwaest
2020-01-17 20:07:46

Jens Verwaest
2020-01-17 20:09:37

Dan Gump
2020-01-17 21:08:11

Dan Gump
2020-01-18 02:58:05

原文網址 Dan Gump
2020-01-15 22:46:36

Has anyone seen that HeroForge kickstarter with the 3D printed & painted models? How long does everyone think it will take for that technology to arrive at a reasonable price?

翻譯年糕

Ben Hart
2020-01-15 22:51:44