Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Andrew Jordan
2020-02-22 09:54:55

Switching over from Anycubic Grey to the Anycubic clear, anyone using this resin and would mind sharing their exposure settings with me? Using just the photon, not the Photon S. Thank you in advance!

翻譯年糕

原文網址 Andrew Jordan
2020-02-02 15:39:12

Does anyone have any idea as to why prints that I used to be able to print without an issue are now failing? The bases are pulling off of the supports and only on one side, Ive printed numerous successful batches of these but am now running into an issue. I did just change the fep tonight, tuned it to 320khz. Do I have have to edit the supports again or? Any ideas would be appreciated. (The base that’s been pulled off in the first picture is the front right model in the second).

翻譯年糕

Benjamin Matthew Harding
2020-02-02 15:48:11

Andrew Jordan
2020-02-02 15:52:50

Corey Faure
2020-02-02 15:56:36

Andrew Jordan
2020-02-02 16:07:25

Dimas Putro Arnindyo
2020-02-02 16:46:51

Andrew Jordan
2020-02-02 16:52:03

Dimas Putro Arnindyo
2020-02-02 16:52:56

Andrew Jordan
2020-02-02 16:54:23

Dimas Putro Arnindyo
2020-02-02 16:57:29

Corey Faure
2020-02-02 17:00:18

Andrew Jordan
2020-02-02 17:02:31

Simon Wilson
2020-02-02 17:08:06

Andrew Jordan
2020-02-02 17:22:28

Andrew Jordan
2020-02-02 17:23:09

Simon Wilson
2020-02-02 17:23:10

Simon Wilson
2020-02-02 17:25:53

Andrew Jordan
2020-02-02 17:28:03

Andrew Jordan
2020-02-02 17:33:47

Dimas Putro Arnindyo
2020-02-02 17:37:20

Luke Mason
2020-02-02 17:46:29

Andrew Jordan
2020-02-02 18:03:11

Simon Wilson
2020-02-02 18:28:15

Johannes Weis
2020-02-02 19:53:29

Andrew Jordan
2020-02-03 11:57:33

Andrew Jordan
2020-02-03 12:02:09

Luke Mason
2020-02-03 12:47:59

Andrew Jordan
2020-02-03 12:54:05

Scott Pavlich
2020-02-03 13:44:14

Andrew Jordan
2020-02-03 13:54:58

Johannes Weis
2020-02-03 14:24:47

Andrew Jordan
2020-02-03 14:36:43

Johannes Weis
2020-02-03 14:48:35

Andrew Jordan
2020-02-03 14:52:44

Ivan Adhi R
2020-02-03 16:46:41

原文網址 Andrew Jordan
2020-02-01 11:12:28

Had some issues with a print of mine earlier, the tail and two front legs and I think the wing failed. Anyone have suggestions on what could be changed to fix this?

翻譯年糕

Himsky Massaoka
2020-02-01 11:33:34

Andrew Jordan
2020-02-01 11:39:57

原文網址 Andrew Jordan
2020-01-20 06:49:06

Does anyone know what could cause the base of this mini to warp? Fairly new to using the Anycubic so any advice would be helpful! Thank you in advance!

翻譯年糕