Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Ng Yu Sheng
2020-02-19 14:07:45

Just an update on my previous prints:

Thank you so much to those who gave me great advice that helped me refine my post-print processing!

I cleaned my prints in dirty IPA then cleaned it in clean IPA.

1st pic: The space marine came out cleaner because I UV cured it under direct sunlight

2nd pic: The space marine had "snow" like coats because I put it in the UV oven straight, without letting it dry.

Last Pic: The 2 space marines which I cured under UV sunlight

Findings:

The cleaner the IPA, the better the final finish. However, to ensure your print does not get white coats, ensure to clean it properly, THEN dry it , THEN cure it.

Correct me if I am wrong but I think the uncured resin will tend to stick unto the print while you wash it , so ensure your print is dry before curing it.

翻譯年糕

Ng Yu Sheng
2020-02-19 14:16:08

Andy Johnny Young
2020-02-19 14:17:40

Ng Yu Sheng
2020-02-19 15:05:01

Ng Yu Sheng
2020-02-20 09:23:37

原文網址 Ng Yu Sheng
2020-02-17 11:49:38

My very first figurine print! Used Anycubic Clear green resin
Exposure time : 10s
Layer height : 0.02mm
off time : 3s
bottom exposure : 50s
layers : 4

Not sure why there are white spots on the models after it cures under the sun. Any recommendations to make it better?

翻譯年糕

Ryan Hockersmith
2020-02-17 12:13:21

Ng Yu Sheng
2020-02-17 12:41:46

Fred Bey
2020-02-17 12:47:03

Ng Yu Sheng
2020-02-17 12:55:59

Ryan Hockersmith
2020-02-17 12:56:38

Fred Bey
2020-02-17 12:58:03

Vinny Bryant
2020-02-17 18:10:07

Vinny Bryant
2020-02-17 18:10:10

Dallas Winston Fitzgerald
2020-02-17 20:39:16

Ng Yu Sheng
2020-02-18 08:39:57

Ng Yu Sheng
2020-02-19 14:12:36

Vinny Bryant
2020-02-19 19:29:02

Ng Yu Sheng
2020-02-20 09:25:35

Vinny Bryant
2020-02-20 09:27:42

Ryan Hockersmith
2020-02-20 09:27:52

原文網址 Ng Yu Sheng
2020-02-01 23:17:18

Hi , I am an amateur at SLA printing and am currently using the Anycubic Photon S to get my prints. I tried using the Ameralabs test print to test the settings for 3Dresyns’ NG 3Dresyn FA30 Clear.

However, I have yet to get any workable results as I’m not sure how to optimise the parameters using the photon slicer to get a reasonable print.

I’ve done the XP finder test too and I could barely see anything forming on the layer.

Really need a way to find out the parameters for my elastic resin, thank you!

Photos ( from nearest to furthest ) : exposure time - 8, 10, 14 , 16 , 18s respectively.

翻譯年糕

原文網址 Ng Yu Sheng
2020-01-30 12:47:30

Hi , I am an amateur at SLA printing and am currently using the Anycubic Photon S to get my prints. I tried using the Ameralabs test print to test the settings for 3Dresyns’ NG 3Dresyn FA30 Clear.

However, I have yet to get any workable results as I’m not sure how to optimise the parameters using the photon slicer to get a reasonable print.

I’ve done the XP finder test too and I could barely see anything forming on the layer.

Really need a way to find out the parameters for my elastic resin, thank you!

翻譯年糕