Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Jenny Searcy
2020-02-18 23:58:50

Low tech approach to resin curing cabinet: 3D solar turntable/$9, 6w resin cure light/$26, leftover Amazon box/ “priceless”. So far so good.

翻譯年糕

Jenny Searcy
2020-02-19 00:03:18

Peter Fulton
2020-02-19 00:03:33

Peter Fulton
2020-02-19 00:03:57

Jenny Searcy
2020-02-19 00:06:56

Jenny Searcy
2020-02-19 00:11:22

Jenny Searcy
2020-02-19 00:16:11

Zachary Carr
2020-02-19 00:17:00

Matteo TheGame Giovannetti
2020-02-19 00:17:08

Jenny Searcy
2020-02-19 00:17:44

Matteo TheGame Giovannetti
2020-02-19 00:18:50

Jenny Searcy
2020-02-19 00:20:51

Peter Fulton
2020-02-19 00:21:07

Spiller Alessandro
2020-02-19 00:22:04

Jenny Searcy
2020-02-19 00:28:01

Daniel Ferguson
2020-02-19 00:28:03

Zac Linhart
2020-02-19 00:55:32

Jenny Searcy
2020-02-19 01:40:32

Zac Linhart
2020-02-19 01:51:15

Zac Linhart
2020-02-19 01:51:46

Jenny Searcy
2020-02-19 01:55:46

Matteo TheGame Giovannetti
2020-02-19 02:09:16

Zac Linhart
2020-02-19 02:10:06

Matteo TheGame Giovannetti
2020-02-19 05:35:16

Michael Bradley-Robbins
2020-02-19 06:19:33

Jenny Searcy
2020-02-19 06:39:50

Michael Bradley-Robbins
2020-02-19 08:57:45

Tom Gannon
2020-02-19 09:07:40

Zac Linhart
2020-02-19 13:09:27

Christopher Barnes
2020-02-19 13:14:35

Adam Michael Hennebeck
2020-02-19 15:45:54

原文網址 Jenny Searcy
2020-02-16 12:21:25

Ok i did the anycubic test cube thingy and it printed flawlessly using AC aqua blue. I think the settings were 30s and 8s Next tried a small figure of an astronaut same settings. After a couple if hours when the plate got high enough to see under it, I saw that there was nothing attached to the upper build plate. Removed everything and found a printed piece stuck to the fep about 2-3mm thick...
Next upped the exp time to 10s and 40s....same thing happened. Ideas?

翻譯年糕

Scott Pavlich
2020-02-16 12:33:52

Jenny Searcy
2020-02-16 12:46:12

Jenny Searcy
2020-02-17 03:11:00

Scott Pavlich
2020-02-17 03:49:18

原文網址 Jenny Searcy
2020-02-16 08:05:59

I have a question... why do several places on the net, sellers, etc refer to the photon as a DLP resin printer?

翻譯年糕

Will Noon
2020-02-16 08:12:19

Jenny Searcy
2020-02-16 08:40:57

Will Noon
2020-02-16 08:42:26

Rob Brzez
2020-02-16 09:03:43

Brandon Ray
2020-02-16 09:07:33

Stefan Giudici
2020-02-16 09:18:30

Jenny Searcy
2020-02-16 09:37:40

Rob Brzez
2020-02-16 10:03:39

Jenny Searcy
2020-02-16 10:19:13

Nipuna Gunarathne
2020-02-18 01:56:05

原文網址 Jenny Searcy
2020-02-16 01:39:05

I just want to say....got a Nova3D Elfin last week, messed with it for about 20 hrs trying to get a decent print. Finally got one only to have the on/off switch stop working. Boxed up sent back.

Ordered Anycubic Photon LCD same day. Set up and zeroed and printing in about 15 min. Printing test cube now (looks good so far). Smell seems not as noticeable. Quiet. So far I’m impressed. What a world of difference!

翻譯年糕

Zena Andreou
2020-02-16 01:45:38