Anycubic Photon Printer Owners 造訪社團

原文網址 James Vincent Paquette
2019-12-09 08:16:42

who are some good content providers? I already support Hex3D on patreon, but i'm always on the lookout for new stuff.

翻譯年糕

原文網址 Daniel Kelly
2019-12-09 08:16:40

原文網址 Fred Breton
2019-12-09 08:16:13

Epic boss from AG Patreon, just need to finish the base. Monocure rapid grey and monocure matte pla for the base.

翻譯年糕

原文網址 Sam Spencer
2019-12-09 08:14:46

Is there a way to reduce the contact size of the support to the model in the Prusa Slicer?

翻譯年糕

Brian Lindley
2019-12-09 08:32:54

原文網址 Jon Weger
2019-12-09 08:08:03

3d printing friends and those who appreciate pop culture goodness. I give you my 3d printed Die Hard Christmas ornament. Check it out. Free Files for the ornament included.

https://youtu.be/QAAdlVyD-fk

翻譯年糕

Darren Donovan
2019-12-09 10:58:38

Jon Weger
2019-12-09 11:46:37

Martin Forsyth
2019-12-10 08:03:50

Jon Weger
2019-12-10 08:22:32

Martin Forsyth
2019-12-10 08:35:06

Jon Weger
2019-12-10 08:38:40

Martin Forsyth
2019-12-10 08:39:29

Martin Forsyth
2019-12-10 08:40:00

Jon Weger
2019-12-10 08:43:40

原文網址 Dean Eyre
2019-12-09 07:56:02

Getting a bit fed up with only 60% successful prints.
Here's the latest failure. I added extra supports thean what the slicer program but, I also thickened them up but it looks like the top part of the support hasn't thickened up. How do I do that at?

翻譯年糕

Michael J Morris
2019-12-09 07:58:48

Jeff Fitch
2019-12-09 08:15:35

Scott Pavlich
2019-12-09 08:20:21

Chad Elstad
2019-12-09 08:26:48

Braad Harild
2019-12-09 08:37:39

Dean Eyre
2019-12-09 08:39:31

Dean Eyre
2019-12-09 08:40:20

Gary Houser
2019-12-09 08:48:33

Brian Lindley
2019-12-09 09:11:23

Dean Eyre
2019-12-09 12:14:18

Dean Eyre
2019-12-09 12:14:29

Jérôme Beyaert
2019-12-09 13:12:06

Dean Eyre
2019-12-09 17:19:30

Ian Gill
2019-12-09 17:54:12

Cory Dolbashian
2019-12-10 05:06:31

原文網址 Juan Carlos Ramirez
2019-12-09 07:40:21

Again Anycubic Amy Liao and warning for all new photon users with the upgrade Photon printer (PTB2BK Fauxton)
The carriage get stuck and hit into the top. I raised a ticket today for fix that. The reason? because remember the upgraded photon come with the new photonS main board and that printer has different height. Temporal solution you can remove the blue plate in the top but if you leave like that your stepper driver will get burn. I tried to modify the height value with a gcode file but remember this new mainboard cannot read these type of files. So when you receive your ned photon printer you need to remove the top blue plate in the printer until Anycubic send a new solution or firmware upgrade only just for new upgrade photon printers. Very Smart Anycubic you're disaster. ? https://youtu.be/Pry1cGqwQ_I In the video I powered off before to get stuck because I don't want to burn the stepper driver and the motor sounds forced. Regards. 翻譯年糕

Juan Carlos Ramirez
2019-12-09 07:42:42

Ben Johnston
2019-12-09 07:50:19

Juan Carlos Ramirez
2019-12-09 07:59:14

Juan Carlos Ramirez
2019-12-09 08:00:35

Ben Johnston
2019-12-09 08:02:15

Juan Carlos Ramirez
2019-12-09 08:04:57

Juan Carlos Ramirez
2019-12-09 08:06:37

Kevin Boogaard
2019-12-09 15:56:17

Sen Kun
2019-12-09 17:49:16

Kevin Boogaard
2019-12-09 17:56:01

Amy Liao
2019-12-09 18:24:45

Juan Carlos Ramirez
2019-12-09 20:29:34

Juan Carlos Ramirez
2019-12-10 11:08:16

原文網址 Jake Gilmore
2019-12-09 07:38:57

原文網址 Katherine Hubis
2019-12-09 07:24:14

Another issue that's probably been solved a million times already:

First time needing to replace FEP (original finally started leaking), so I replaced it, and recalibrated home/leveled the print plate. I used the paper method to level.

I used a print file that has been 100% successful in the past, but while one side printed perfectly, the other half stuck to the FEP.

Now! I have had vat-sticking previously, but it had always been support issues, not leveling or exposure settings, so I'm concerned that I messed up the FEP install somehow.

Should I just attempt to level the plate again and hope I don't keep sticking, or is there a way to make sure the vat isn't interfering somehow?

翻譯年糕

Michael Tetreau
2019-12-09 07:27:04