Anycubic Photon Printer Owners 造訪社團

原文網址 Josh Dalgliesh
2020-03-07 14:14:25

So I've noticed that there seems to be a lot of newcomers of late (myself included). Just came across a video that consolidates a lot of good modelers and thought to myself that this video would have definitely been a good starting point/helpful for find minis that are perfect for me had I not already found them. So if you're wondering what to print next, I hope this year old video helps :)
https://www.youtube.com/watch?v=pbcw-wce6uA 翻譯年糕

原文網址 Richard Burke
2020-03-07 14:09:43

So. Got my printer working well. Hot water fixed my support issue. Now i have this white residue poping up. What is the cause of this. How to if i need to avoid it? Will it interfere with primeing and painting ?

翻譯年糕

Mike Kelso
2020-03-07 14:11:08

Nipuna Gunarathne
2020-03-07 14:17:14

Richard Burke
2020-03-07 14:25:41

David Belshaw
2020-03-07 14:55:50

Fred Bey
2020-03-08 00:03:59

Herllon Alves
2020-03-08 06:23:51

原文網址 Jacob William Curtis
2020-03-07 14:00:59

Hey Folks,

I'm having some prints come out slightly deformed. do I need more supports for the lowest points? I tried increasing exposure time with this resin to slightly above the recommendations, and the room I'm printing in is about 70F.

翻譯年糕

Scott Pavlich
2020-03-07 15:50:35

原文網址 Marnie Jefferson
2020-03-07 13:48:41

Screen installed but when I run the UV detection that I all that appears. Would that mean that the mirror like layer on the bottom was a protective film despite it being very hard to attempt to peel off?

翻譯年糕

Bert Harvey
2020-03-07 13:56:42

Marnie Jefferson
2020-03-07 15:01:14

Bert Harvey
2020-03-07 15:02:15

Scott Pavlich
2020-03-07 15:36:57

Marnie Jefferson
2020-03-07 17:26:58

原文網址 Stefan Arnautu
2020-03-07 13:44:22

Mike Armijo
2020-03-07 21:42:11

原文網址 Brett Hogan
2020-03-07 13:36:21

I have seen the PDF for the settings for using Anycubic resin but that's at .05 layer height. But i want to do .02 or .01 layer height. Would I use the same settings?

翻譯年糕

John Chrapkowski
2020-03-07 13:38:38

John Chrapkowski
2020-03-07 13:39:10

Bob Deblier
2020-03-07 13:41:35

Scott Pavlich
2020-03-07 15:41:10

Scott Pavlich
2020-03-07 15:41:25

Scott Pavlich
2020-03-07 15:42:16

Scott Pavlich
2020-03-07 15:42:45

Scott Pavlich
2020-03-07 15:43:57

原文網址 Marnie Jefferson
2020-03-07 13:05:26

I am going through the process of replacing my screen. Do I remove this film of the top or is this screen DOA?

翻譯年糕

Blaine Tsukayama
2020-03-07 13:07:33

Brian King
2020-03-07 13:07:38

Michael Szita
2020-03-07 13:07:44

Jarin Udom
2020-03-07 13:08:07

Marnie Jefferson
2020-03-07 13:08:18

Marnie Jefferson
2020-03-07 13:14:36

Michael Szita
2020-03-07 13:18:39

Marnie Jefferson
2020-03-07 13:20:12

Michael Szita
2020-03-07 13:21:11

Marnie Jefferson
2020-03-07 13:23:40

Peter Martinez
2020-03-07 14:46:51

Marnie Jefferson
2020-03-07 14:59:23

Scott Pavlich
2020-03-07 15:15:40

Michael Szita
2020-03-07 15:19:46

Scott Pavlich
2020-03-07 15:26:23

Christopher Fugate
2020-03-10 00:30:08

原文網址 Mata Mac Gille Fhionntain
2020-03-07 12:56:09

What things am I considering when doing a print in place/flexi item like the Trilobite posted earlier. Not that specific one, but there are some I would like to print like this one......

翻譯年糕