Anycubic Photon Printer Owners 造訪社團

原文網址 Tyron Craft
2020-03-06 07:24:24

Anyone else stocking up on resin for the impending doom of 14 days home arrest?
# coronavirus # screwtoiletpapermoreresin

翻譯年糕

原文網址 Derek Lee Thompson
2020-03-06 07:24:13

My wife and I realized that Printers are Prepers. Everyone is rushing out to buy Rubber gloves and masks and hand sanitizer. WE have all of that just for our printer....WE are set.

翻譯年糕

原文網址 Josh Singleton
2020-03-06 07:02:47

When replacing the photon lcd with the elegoo mars screen, does the connector go the same direction as you pull off the stock one? I have read some people put the connector on the wrong way and damaged their board

翻譯年糕

原文網址 Tamas Somogyi
2020-03-06 06:34:04

(Temperature control v0.0001) I hardly dare to post my patchwork.... Let me know your thoughts...
I had to dump her in the cellar just in case something goes wrong tonight.... :)

(溫度控制v0. 0001)我不敢發布我的補丁.... 讓我知道你的想法...
我不得不把她扔到地窖, 以防萬一今晚出錯.... :)

· 查看原文 · 為此翻譯評分

原文網址 Ryan Tudor
2020-03-06 06:07:31

I tried the exposure test with the monocure file. Any input? The "ctrl v" seems a little faded, perhaps a bit overexposed? Bridge pools good. Side picture shows a vertical thing warping, not sure whatnot gleam from that.
Sorry it's tacky, wanted to ask before I head out for the evening..

翻譯年糕

原文網址 Derek Fontes
2020-03-06 06:01:47

Concerning printing miniatures for tabletop games... I've had pretty good turnout with my prints so far. But I've noticed that my minis are brittle. Particularly long thin areas, usually appendages ( arm, legs and such ). I've only used the clear green that anycubic sent me. They also sent me some black and grey as well. Is there a better resin that I should look into for printing miniatures, or perhaps curing too long or short? I've just let them sit in the sun for the time being, cure chamber parts are en route. I've snapped the legs and a tail off of a few minis now. The detail is crazy good, I'm just afraid to spend the time prepping and painting, just break it.

翻譯年糕

原文網址 Dustin Cole
2020-03-06 06:01:45

Well when I was scraping off my build plate, it adhered too well and i stabbed myself...
# resinzombiegroundzero Well when I was scraping off my build plate, it adhered too well and i stabbed myself...
# resinzombiegroundzero 翻譯年糕

原文網址 Thomas Allen
2020-03-06 05:45:10

Ive been having issues lately with prints not stixking to the buildplate and have tried all sorts of solutions. I was levelling the plate using the flint read method earlier and noticed a grinding noise well before the plate hit the fep. I found this was due to the bracket that connects the build plate to the z axis is hitting the wall of the vat. This means it is impossible for me to complete the flint read plate level and it appears my plate will be stopped by the vat wall before it can properly press the resin to the uv light. Has anyone else experienced this or have any idea how to fix this?

翻譯年糕

原文網址 Ron Israel
2020-03-06 05:35:28

Is it normal for every time my printer does a level it kind of sounds like something is sticking as it releases the model seems to be printing OK though

翻譯年糕

原文網址 Paul Oliveira
2020-03-06 05:21:24