Anycubic Photon Printer Owners 造訪社團

原文網址 Doug Bowman
2020-02-26 07:29:35

Modeled and engineered for printing in ZBrush, printed on my Photon and Ender 3 Pro

翻譯年糕

Josh Bryzelak
2020-02-26 09:02:37

Doug Bowman
2020-02-26 12:59:53

Josh Bryzelak
2020-02-26 13:03:43

Doug Bowman
2020-02-26 13:06:31

原文網址 Ad Puente
2020-02-26 07:18:59

Hi everyone, so, my screen is broken. I found this one online, but its not the same as the one I bought become. Somenody has bought it? IT works fine? Thanks

翻譯年糕

Nicholas Hein
2020-02-26 07:40:41

Brian King
2020-02-26 07:53:00

Nicholas Hein
2020-02-26 07:54:06

原文網址 Tom Barnes
2020-02-26 07:10:36

Hmmm, I wonder how that happened? The supports printed to a point but for some reason the lower arm didn't print... Perplexed somewhat...

翻譯年糕

Will Mckay
2020-02-26 07:15:41

Jeremy Mongoose Harris
2020-02-26 07:18:13

Joseph Bochinski
2020-02-26 07:27:44

Merv Hinton
2020-02-28 20:12:51

John Jones
2020-02-28 22:57:32

原文網址 Ash Fielding
2020-02-26 06:47:01

Note to self check z home after updating firmware ??‍♂️

更新固件後自我檢查z回家 ?? ♂️

· 查看原文 · 為此翻譯評分

Scott Pavlich
2020-02-26 10:59:20

Ash Fielding
2020-02-26 13:31:49

Nicolas Tsagarides
2020-02-26 23:30:38

Ash Fielding
2020-02-27 00:26:00

Nicolas Tsagarides
2020-02-27 02:56:02

Bob Deblier
2020-02-27 16:59:05

原文網址 Kenneth Boshell
2020-02-26 06:22:45

This is a fifty fifty mix of anycubic grey to siraya tenacious. It looks like column eight is the sweet spot. Please help confirm or deny.

翻譯年糕

Atis Papai
2020-02-26 06:31:59

Zena Andreou
2020-02-26 06:32:21

Zena Andreou
2020-02-26 06:32:57

Zena Andreou
2020-02-26 06:33:07

Kenneth Boshell
2020-02-26 06:57:52

原文網址 Scott Ball
2020-02-26 06:00:42

If I add Flex100 or Tenacious to my resin (anycubic grey) should i change my settings such as exposure? I've heard 75/25 ratio works well, what are your preferences? Thanks as always!

翻譯年糕

Kenneth Boshell
2020-02-26 06:28:04

Bob Deblier
2020-02-26 16:54:33

Darko Miljak
2020-02-26 18:35:04

原文網址 Mat Greeley
2020-02-26 05:56:22

Hey everyone, I just replaced my mainboard, but now I'm getting a blank white screen on the interface when I start it up. Anyone have any suggestions?

翻譯年糕

Mat Greeley
2020-02-26 06:02:17

原文網址 Aaron Marino-Drake
2020-02-26 05:30:19

Question:

My prints aren't adhering to the build plate. The only difference since I last printed was an update to Chitubox. Plate is level, cleaned everything before hand, profile settings didn't change, what do?

翻譯年糕

Ryan Shelvik
2020-02-26 05:34:34

Aaron Marino-Drake
2020-02-26 05:35:17

Bob Deblier
2020-02-26 16:30:37

原文網址 Sandro Pateishvili
2020-02-26 05:28:31

Greetings, what is a reasonable way to count the volume of resin used? How inacurate is Chitubox?

I know I have to add around 5-10% for run off and all that

翻譯年糕

Paul Yanzick
2020-02-26 05:29:05

Sandro Pateishvili
2020-02-26 05:54:52

Chad Elstad
2020-02-26 06:12:07

Paul Yanzick
2020-02-26 06:12:23

原文網址 Jenny Searcy
2020-02-26 05:20:14

Quick question re multiple prints at same time. Different resins mostly siraya fast and eegloo red clear. Exposure 65/8. Layer height .05 bottom layers 3. No supports. Have releveled to be sure that is not the issue.
The problem I’ve experienced x3 is that if I place more than 1 of the same object on the build plate to be printed only 1 or 2 out of 4 print, there is some buildup on the fep where the other objects should have printed of 3-4 layers approx. There is adequate space between the objects but not too much and none of them are close to any of the borders.
Am I not spacing properly? More exp time because of the mult objects? Suggestions, thiughts?

翻譯年糕

Cynthia Duehr
2020-02-26 06:40:23