Anycubic Photon Printer Owners 造訪社團

原文網址 Pablo Rovira
2020-02-08 04:21:19

very nice !

原文網址 Pablo Rovira
2020-02-08 03:49:23

Hi... Somebody could advise on how to -step by step- interpret these results (both pictures are the same only difference is flash). On GitHub and thingiverse there is no column multiplier for this test, nor clear instructions. Thanks!

翻譯年糕

Bastian Dietert
2020-02-08 03:54:02

Pablo Rovira
2020-02-08 03:57:16

Bastian Dietert
2020-02-08 03:57:33

Pablo Rovira
2020-02-08 03:58:09

Bastian Dietert
2020-02-08 03:59:36

Pablo Rovira
2020-02-08 04:02:28

原文網址 Howard Kyle
2020-02-08 03:45:14

Thanks for the add. Question about hardware so the screw in the back won’t turn when the build plate gets low to start a print so my last two prints haven’t even gotten out of the vat what can I do I love my photon and would love to get it back.

翻譯年糕

Niall Forrester
2020-02-08 13:51:24

Howard Kyle
2020-02-09 11:04:33

原文網址 Travis Nelson
2020-02-08 03:40:49

I'm about to run out of my free bottle of Anycubic green and need to purchase my next bottle. What's your favorite resin you have used and why?

翻譯年糕

Alexander Bayerdorffer
2020-02-08 03:53:53

Smith Hayward
2020-02-08 04:13:52

Patrick Harland
2020-02-08 04:19:22

Travis Nelson
2020-02-08 04:34:12

Alexander Bayerdorffer
2020-02-08 04:35:18

Denlee Paddy Rhodes
2020-02-08 04:42:11

Gabe Snooks
2020-02-08 04:46:13

Shinagamei Cooley
2020-02-08 04:54:20

Aaron Frith
2020-02-08 05:34:37

Keith O'Donnell
2020-02-08 07:35:07

Chris Holden
2020-02-08 07:56:48

Michael Pippin
2020-02-08 07:58:45

Mark Bryner
2020-02-08 08:08:37

Erik Herman
2020-02-08 11:00:14

Maria Byrd
2020-02-08 11:20:36

Clint B. Kauffman
2020-02-08 12:14:48

Clint B. Kauffman
2020-02-08 12:15:46

Jason Jacobs
2020-02-08 12:21:54

Shawn O'Hara
2020-02-08 13:37:30

Yannik Tillmann
2020-02-08 14:24:38

Joe Garry
2020-02-08 15:07:32

Rick Hanson
2020-02-09 00:10:29

Neil Castle
2020-02-09 02:31:02

原文網址 Cody Wishart
2020-02-08 03:40:43

Is it bad if the resin has an abnormal amount of air bubbles when you put it into the vat? Is it bad if the resin has an abnormal amount of air bubbles when you put it into the vat? 翻譯年糕

Jarin Udom
2020-02-08 03:41:25

James Hendrix
2020-02-08 03:46:38

Dan Andersson
2020-02-08 03:56:36

Kempster Kevin
2020-02-08 04:02:46

Cody Wishart
2020-02-08 04:03:13

Charlie Yoshi Locke
2020-02-08 06:05:16

Rigo Arevalo
2020-02-08 06:12:12

Richard Shapiro
2020-02-08 07:17:00

原文網址 Michael Aaron Carroll
2020-02-08 03:32:44

Whoops! Somehow my ultrasonic cleaner got set from 3 minutes to 30 minutes. Entire 3D printed chess set is going in the garbage.
I have my ultrasonic cleaner filled with plain tap water. I put my parts to be cleaned inside a tough Ziploc bag and fill it with isopropanol and then put the bag in the cleaner.

翻譯年糕

John Chrapkowski
2020-02-08 03:33:49

Keith Michael Harrington
2020-02-08 03:35:28

Michael Aaron Carroll
2020-02-08 03:38:58

Jim Monaco
2020-02-08 03:40:44

Khoa Truong
2020-02-08 04:02:13

Robert Small
2020-02-08 04:38:57

Michael Aaron Carroll
2020-02-08 11:00:36

Azeem Hussein
2020-02-08 23:32:54

原文網址 Keith O'Donnell
2020-02-08 03:24:34

Oh boy!

Failed LCD or...

翻譯年糕

Ryan Shelvik
2020-02-08 03:26:42

Ed Horn
2020-02-09 05:58:09

原文網址 Christopher Carfi
2020-02-08 03:14:03

Anyone else hear random beeps during print? Prints seem fine but around 16% I get a single beep and it’s driving me nuts.

翻譯年糕

Harold Crossley
2020-02-08 05:54:25

原文網址 David Minford
2020-02-08 03:12:03

This is primarily for UK users.
I seen someone on the fourms recommending this stuff to clean uncured resin from prints.
So I've been using it on various models today.
I've used it neat in a ultrasonic bath, and it's a decent cleaner, it removes alot of uncured resin.
I still need to swirl it in some ipa to remove the final "tacky" feel to the part.
Over all its OK, cheap and safe to use in a ultrasonic bath.

I still prefer acetone, 30 to 40 secs and it's completely removed the uncured resin.

翻譯年糕

Matt Hooton
2020-02-08 03:42:16

David Minford
2020-02-08 05:08:15

Matt Hooton
2020-02-08 05:12:59

David Minford
2020-02-08 06:08:15

Nicolas Tsagarides
2020-02-08 17:40:25

David Minford
2020-02-08 19:26:09

Nicolas Tsagarides
2020-02-08 20:32:03

原文網址 Daniel Feeney
2020-02-08 03:08:35

So my photon seems to have stopped recognizing the USB with all of the vital and print files. Whenever I hit 'print', it just shows me four blank white squares. The USB reads correctly when inserted into my PC. What could be the issue here?

翻譯年糕

Nipuna Gunarathne
2020-02-08 03:16:26