Anycubic Photon Printer Owners 造訪社團

原文網址 Vincent Balmont
2019-12-26 12:19:37

He came out pretty good. 2 drain holes 1.5mm wall。 over did it on the heavy supports though I think

翻譯年糕

Dawid Van Der Merwe
2019-12-26 12:47:33

Vincent Balmont
2019-12-26 12:48:10

Joey Smith
2019-12-26 14:36:09

Jarin Udom
2019-12-27 11:59:03

原文網址 Ray Hancock
2019-12-26 12:16:13

Well... I got my first photon as a Christmas gift on Sunday night... and my second one today lol. I’m pretty okay with it... but that escalated quickly lol

翻譯年糕

Tomas Salo
2019-12-26 19:01:14

James Edward
2019-12-26 19:25:48

Neil Ramsay
2019-12-26 22:33:06

Ray Hancock
2019-12-27 00:01:37

Bruno Tabarani
2019-12-27 00:25:12

Eric Ilaqua
2019-12-27 08:54:35

Josh Ford
2019-12-27 10:27:30

John Rasmussen
2019-12-27 10:50:51

Ray Hancock
2019-12-27 12:41:43

John Rasmussen
2019-12-27 12:41:59

Ray Hancock
2019-12-27 12:42:33

John Rasmussen
2019-12-27 12:43:17

Ray Hancock
2019-12-27 12:44:49

原文網址 Brian Romine
2019-12-26 12:15:41

What cleaning solution do you folks use for cleaning prints in an ultrasonic cleaner?

翻譯年糕

Jedediah Burger
2019-12-26 12:20:23

Tiernan Messmer
2019-12-26 12:22:11

Jeff Johnson
2019-12-26 12:28:46

Justin Coles
2019-12-26 12:43:36

Alex Danis
2019-12-26 13:21:50

Marty Khull
2019-12-26 14:22:56

Joey Smith
2019-12-26 14:30:52

Marcin Jażdżewski
2019-12-26 16:16:12

Fredrik Hjelm
2019-12-26 17:12:30

Fredrik Hjelm
2019-12-26 17:13:38

Fredrik Hjelm
2019-12-26 17:14:48

Dave Williams
2019-12-26 18:27:41

Jim Nelson
2019-12-26 18:30:11

Tom Howley
2019-12-28 05:00:39

原文網址 Christopharius Cruzantium
2019-12-26 12:01:21

Well, baby yoda Christmas ornament present seems to have gone over well with my better half! At least the printing area gets to stick around for a while ?

Elegoo Gray .03 layers

翻譯年糕

原文網址 Patrick Sean Stock
2019-12-26 11:48:38

Will this keep me from being able to print? I nicked the film. It didn't go through, but caused a raise in it, that little hump above my finger tip in the picture below.

翻譯年糕

Fred Bey
2019-12-26 11:51:45

Patrick Sean Stock
2019-12-26 11:54:34

Fred Bey
2019-12-26 11:55:18

Patrick Sean Stock
2019-12-26 11:55:38

Fred Bey
2019-12-26 11:55:59

Jeremy Babcock
2019-12-26 11:56:08

Patrick Sean Stock
2019-12-26 11:56:42

Jeremy Babcock
2019-12-26 11:57:42

Nick Robinson
2019-12-26 12:47:40

原文網址 Daniel Ramirez
2019-12-26 11:29:00

Love this machine, first set of minis.

翻譯年糕

Jake Walker
2019-12-26 12:10:10

Daniel Ramirez
2019-12-26 12:47:16

Antoine Andary
2019-12-26 16:29:51

Justin Cupitt
2019-12-26 18:24:45

原文網址 Kevin A Thompson
2019-12-26 11:28:24

Having a print issue & looking for advice.

When I print a multi-sectioned piece with pegs & holes to assemble the entire model, they never seem to fit together. The pegs always seem just a few thou thicker than the hole it is meant to go into. I end up having to dremel down the diameter of the pegs just to get them to fit.

This has been happening to me across multiple models, not just one or two. If I print multiple pieces, they just don't fit together without modification.

I am using Filaments.ca Polyjuice for resin on an original Photon. Any thoughts what settings I should be changing?

翻譯年糕

Steven Molen
2019-12-26 11:32:47

原文網址 Gary Bunda
2019-12-26 11:27:35

Does anyone else have issues removing the build plate on the Photon S? It really sticks on mine but I thought it would get better with it being removed and replaced but it seems to maybe getting worse.

翻譯年糕

原文網址 Dom TheIcoN Manchisi
2019-12-26 11:17:51

What I did for xmas

翻譯年糕

原文網址 Josh Aleckson
2019-12-26 11:03:01

Help! Just got the Photon. New to resin printing, but not 3D printing. My first 2 prints had some issues that I think I fixed, but now the prints are all sticking to the bottom of the vat. What could cause that?

翻譯年糕

Grant Kinnick Smith
2019-12-26 11:04:26