Taiwan自動控制設備交流 造訪社團 » 用戶發文

原文網址 楊欽雄
2018-08-03 19:33:55

想請教一個關於馬達的問題
目前我有使用五相的步進馬達
有沒有可能不換驅動器換馬達呢?

譬如我目前用東方的馬達+東方的驅動器,譬如透過轉接或是改線,可以換成台達的馬達+東方的驅動器嗎?

Kirk Fang
2018-08-03 20:20:17

吳日上
2018-08-03 20:32:35

帥小政
2018-08-03 21:09:16

楊欽雄
2018-08-03 21:11:48

鄭小白
2018-08-03 22:41:46

楊欽雄
2018-08-03 22:43:21

廖唯任
2018-08-04 17:12:51

Woni Yang
2018-08-04 18:03:47

帥小政
2018-08-04 20:17:16


原文網址 楊欽雄
2018-07-06 17:14:43

這個輪子哪裡買得到呢?直徑20MM

林大師
2018-07-06 17:55:51

Min Chien Huang
2018-07-06 19:05:15

Su Wu
2018-07-06 19:17:18

曾安輝
2018-07-06 19:43:14

Vincent Tsai
2018-07-06 20:04:36

曾安輝
2018-07-06 20:09:23


原文網址 楊欽雄
2018-03-11 20:55:28

目前設備上有使用OMRON的蜂鳴器(圖片兩種都有用過)
http://www.omron.com.tw/Images/l_1106-18-118973-198x198.jpg

因為現場比較吵
使用起來覺得都還是很小聲
請問有沒有其他推薦的蜂鳴器呢?
因為16mm的洞已經挖好,所以希望是可以直接套入的

或是有什麼方法可以讓聲音更大聲?譬如放個喇叭等

I-Tang Liang
2018-03-11 21:27:59

林祐群
2018-03-11 21:47:42

Luke Lee
2018-03-11 22:03:36

陳建霖
2018-03-11 22:09:08

Ya Ng
2018-03-11 22:27:06

呂可松
2018-03-11 23:34:34

I-Tang Liang
2018-03-12 07:56:58

曾安輝
2018-03-12 17:17:21

詹益瑞
2018-03-14 12:25:23

詹益瑞
2018-03-14 12:25:29

許家豪
2018-03-16 18:45:54


原文網址 楊欽雄
2018-02-12 16:07:32

說明書看不懂
想詢問各位前輩

以下是伺服壓床的說明書其中一段
是講CCLINK與PLC連線時
如何透過PC寫入暫存區內
有前輩可以大概說一下是什麼意思嗎?
主要是卡在TOP+?這邊
是指說我原有的暫存區位置+?的意思
或是有其他的意思呢?

I/O memory assignments are not made by specifying individual registers for the 14 words, but by assigning the top register numbers for input and output, from which the successive registers are then assigned in order. For example, the following registers are used for the Fieldbus domain if input and output is assigned with the top register 110 and 190, respectively:

Input 110, 111, 112, 113, 114, 115, 116, 117, 118, 119 (10 words)

Output 190, 191, 192, 193 (4 words)
In explanations hereafter, the individual numbers (register address) are referred to as the following:
Input top +0, input top +1, input top +2, ..., input top +9
Output top +0, output top +1, output top +2, output top +3
The “input top +1” command register specifies the type of operation. However, check whether or not it is possible to execute the command before doing so. The command can be executed if the lowest bit of status register 1 for “output top+0” is 1.
After setting the command code and required parameter (value), set the lowest bit from 0 to 1 for the “input top +0” control register to execute the command. The lowest bit needs to be retained as 1 for at least 10 msec.
If the command is executed, the lowest bit for the “output top +0” status register 1 becomes “0: busy” (*2) and after the command is processed, it reverts to “1: execution possible.” If some sort of execution error occurs, the bit 1 for the status register (output top +0) becomes “1” (error occurred). Read the error code for status register 2 (output top +1) and attend to the error.
The following pages show a flowchart and timing chart for the program creation registers.

翻譯年糕


原文網址 楊欽雄
2016-03-24 22:47:59

有人可以推薦一下墊片給我嗎
要耐熱300度以上
耐摩擦
厚度大概0.2~0.3mm左右
面積大概要直徑50mm的圓
有彈性可彎
謝謝大家

翁嘉良
2016-03-25 11:41:05

楊欽雄
2016-03-25 15:35:49

李冠群
2016-03-25 15:48:39

楊欽雄
2016-03-25 17:18:42

羅彥澄
2016-03-25 18:13:41

楊欽雄
2016-04-01 11:12:13

Ahone Liu
2016-04-14 18:44:58

陳煥昌
2016-04-17 01:27:10


原文網址 楊欽雄
2015-11-10 09:55:06

遇到一個工具的問題想請教大家

有兩塊鐵板兩邊有皮帶拉住
最近想找個工具
類似千斤頂那種東西,但是體積不能太大,大約5cm左右
水平放進去鐵板間,然後可以手動伸長到10cm頂住兩塊鐵板
我再把鐵板螺絲鎖好固定,這樣我就可以確保皮帶被拉撐
有這種東西嗎?

楊欽雄
2015-11-10 11:27:57

李冠群
2015-11-10 14:02:04

Jack Huang
2015-11-10 14:21:21

翁嘉良
2015-11-10 15:31:28

Byoung Chen
2015-11-10 23:53:24


原文網址 楊欽雄
2015-08-14 14:08:17

尋找合作廠商,請私訊聯絡
1,位於新竹以北(新竹,桃園,新北,台北)
2.有自己的加工設備(CNC,車床,洗床,工具)可製作治具
3,有自動化整合能力
不論大公司或小工廠,希望有機會可以交流一下

Eric Chen
2015-08-14 17:19:11

詹英仁
2015-08-14 18:09:10

黃思凱
2015-08-14 20:07:56

詹英仁
2015-08-14 22:29:13


 

討論主題

全不選 常用關鍵字