ATOM 3D Printer Group 造訪社團 » ATOM 2.5

Hello can i get help? I am looking for simplify 3d fff data of atom 2.5 ex. All the links in the previous post have been deleted, so I can't get them. I would appreciate your help.

안녕하세요 혹시 도움을 받을수 있을까요 ? 아톰 2.5 ex 의 simplify 3d fff 데이터를 구하고 있습니다. 예전 게시글의 링크들은 다 삭제되어 구할 수가 없네요 도와주시면 감사하겠습니다.

翻譯年糕

小測試～花瓶列印（透明料）

ATOM2.5~順順的～^_^

ATOM2.5~自己配件自己印

列印進料導料小配件

◆賣◆ATOM 2.5 2018/08月拆封組裝

價格：27500

物品狀態：8成新 噴頭 加熱片 感溫晶片皆換新過

連絡方式：私訊+留言

交易地點：淡江自取 其他地方可討論

物品介紹：

畢業設計之後幾乎沒有使用，

因此求售，目前機況正常。

因被放鳥故重po

價錢誠可議，尋找有緣人

任何問題都歡迎私訊我！謝謝大家！

不知這算不算問題或保固問題了，ATOM2.5EX的碳纖桿，第一張照片裡面的磁鐵金屬表層(表皮)破裂了，第二張是正常的模樣，正常使用情況下，潤滑油應該都是白色的，但這端已經磨出黑色油泥了，這樣該不會碳纖桿要全換了吧？

◆賣◆

01. 發文者：我

02. 物品名稱：ATOM 2.5 2018/08月拆封組裝

03. 價格：30000

04. 數量：1

05. 運輸方式：面交

06. 物品狀態：8成新 噴頭 加熱片 感溫晶片皆換新過

07. 連絡方式：私訊+留言

08. 交易地點：淡江自取 其他地方可討論

09.物品介紹：

畢業設計之後幾乎沒有使用，

因此求售，目前機況正常。

價錢誠可議，尋找有緣人

任何問題都歡迎私訊我！謝謝大家！

想請教一下打印Spidermaker, 在Atom 2.5 有冇特別需要設定？

以往打印Spidermaker 十分容易成功的，但當要打印的東西越來越細緻的時候，摩打轉動多了的時候，spidermaker filament會像圖中這樣跑了出來。

會否是Atom 2.5 機件開始老化?

多謝指教。

想請教用過Atom 2.5EX/FX的朋友，如已經升級用Atom 3.0 ，會在哪方面感受到有明確改善？ Thank you .

想請教一下如果Atom 2.5EX打印嘴塞了應該怎樣辦？

Hello everybody,

I would to present to you the different steps of my ATOM 2.5EX printer evolution project:

- Step 1: disassembly of internal electronics + addition of TOP LED rails for lighting (Status => 100% finished)

- Step 2: replacement of the 8-bit motherboard with a 32-bit board (Duet2 Wifi) + addition of Side LED rails for lighting (Status => 100% finished)

- Step 3: development and integration of a 7' paneldue screen on the frame with laser-cutting aluminium parts + folding (Status => 75% finished)

- Step 4: manufacture of a rear plate to integrate the antenna of the Duet2 Wifi board + addition of an inter-switch for the internal lighting of the printer (Status => 75% finished)

- Step 5.1: replacement of the original nozzle with an 24v e-3D v6 standard version + a 24v Dragon Hotend version (Status => in progress 75% finished)

- Step 5.2: developpement and integration of a PCB for rapid disassembly of the print head, it's the same principle as ATOM 2.5 FX (Status => PCB are 100% developped and PCB manufacture is 50% finished)

- Step 5.3: replacement of the 12v power supply with a 24 volt version from Meanwell. (Status => to be mounted)

- Step 5.4: installation of a 24v to 12v converter to keep the original heating bed in 12v. (Status => to be mounted)

- Step 6.0: finishing integration of the 2 DYZE Filament sentinel to be able to stop the print when wire is out.

- Step 7.0 : integration of the ATOM laser module (if possible with the Duet2 Wifi). For this last step, I'm not sure if I can connect and run the laser on the Duet Board. I need to check first...

I will give you news about my project in few days / weeks...

✋

翻譯年糕