Anycubic Photon Printer Owners 造訪社團 » Prusa

原文網址 Colton Wilkins
2020-03-11 11:28:56

Anycubic Translucent Red

It comes out red and clear which I like and I used hot water to get supports off, used the washing and curing station to wash and cure and a small razor to shave down the bumps I’m just curious if anyone has any tips for models like these where you can either;

A. set up supports so they don’t leave marks
Or
B. Method to remove the divits without messing up the finish
Or
C. Any other methods by which to have an easier post part.

I used prusa slicer for optimizes orient and auto supports and manually added my own where need and sliced with the photon slicer.

Any tips or tricks will, I know a lot from research and the forums but obviously not everything.

I feel like I did an okay job removing the divots but you can see the scrape marks.

I’m aware there’s just no getting around the support removal sometimes but the forum knows best!

翻譯年糕

Fred Bey
2020-03-11 11:35:21

Chris Roberts
2020-03-11 11:45:50

Colton Wilkins
2020-03-11 12:12:29

Colton Wilkins
2020-03-11 12:12:40

Christopher Barnes
2020-03-11 12:15:16

Colton Wilkins
2020-03-11 12:22:13

Colton Wilkins
2020-03-11 12:22:44

原文網址 Ben Miller
2020-03-11 10:11:23

Hi all! I have had my photon up and running for a day. This is my second print. First was the photon cube. Would love any feed back if I can improve on this cause I am already pretty happy with the result. .03 layer height. 10 second exposure. And a bunch of other numbers I barely understand. Anyone point me to a good prusa slicer support vid for minis?

翻譯年糕

Ryley Dempsey-Spearing
2020-03-11 10:29:03

Ben Miller
2020-03-11 10:29:44

Jonathan Dunbar
2020-03-11 11:19:05

Ben Miller
2020-03-11 11:26:31

Ryley Dempsey-Spearing
2020-03-11 11:49:52

Jacob Palmer
2020-03-11 15:49:26

Christian Savarda
2020-03-11 21:53:03

Michael Lamberti
2020-03-13 06:46:35

原文網址 Reggie Grahita Adhyatmaka Djatni
2020-03-10 16:32:16

How do you guys get almost perfect result with prusa slicer + chitubox? I always get bad result with that method

翻譯年糕

Chris Holden
2020-03-10 17:04:50

Gustaf Sjögren
2020-03-10 17:28:07

Jacob Palmer
2020-03-10 18:39:47

Reggie Grahita Adhyatmaka Djatni
2020-03-10 18:58:45

Reggie Grahita Adhyatmaka Djatni
2020-03-10 18:59:43

Bob Deblier
2020-03-10 20:22:53

Michael Houx
2020-03-10 21:32:35

Reggie Grahita Adhyatmaka Djatni
2020-03-10 22:32:36

Keith Stringer
2020-03-10 22:37:18

Mark Wardle
2020-03-10 23:21:23

Mark Wardle
2020-03-10 23:21:30

Mark Wardle
2020-03-10 23:21:39

Michael Houx
2020-03-10 23:56:57

Travis McGeathy
2020-03-11 06:59:28

George Bulte
2020-03-11 07:04:45

Travis McGeathy
2020-03-11 07:06:08

Brett VanDyke
2020-03-12 20:00:00

原文網址 Przemysław Ociepa
2020-03-09 01:14:49

In Prusa slicer after auto-generating support points, the supports are below the pad as in the attached photo. So when I export as stl file with supports to Photon slicer I have a problem with first some slices on platform. Could you help where is the problem?

翻譯年糕

Ryan Tudor
2020-03-09 01:17:10

Christopher Hayes
2020-03-09 01:21:59

Przemysław Ociepa
2020-03-09 01:37:14

Christopher Hayes
2020-03-09 03:03:42

Przemysław Ociepa
2020-03-09 04:27:18

Christopher Hayes
2020-03-09 05:53:54

原文網址 T.R. Griffith
2020-03-07 23:32:14

So here's my process, can you tell me if I'm on the right path? Prepare model in Fusion 360 with minor tweaks (models from HeroForge or other places) save as STL. Open in PrusaSlice, auto orient so faces are up. Auto support at 75%. Export w/ supports. Open in ChitUBox and slice. Open in Photon File Validator, fix any issues, if island to big go back to PrusaSlice and adjust as needed. GoTo 3, if not GoTo 5. Put .photon file on good USB and plug into Photon. Print. WAAAIIIITTTT Detach plate, scrape off printed object into ultrasonic jewelry cleaner filled with IPA and set for 3 minutes, Run HOT water over printed object and remove supports. LIGHTLY sand leftover support bumps Place under UV light and rotating stand for 5 minutes (+/- depending on size) Finish (paint if needed, varnish, whatever) Collect Underpants
Profit 翻譯年糕

Kees van Dongen
2020-03-07 23:37:17

Fred Bey
2020-03-07 23:42:18

Donovan Lever
2020-03-07 23:51:13

Tim Parks
2020-03-08 00:08:40

Dan Andersson
2020-03-08 00:19:31

T.R. Griffith
2020-03-08 00:52:02

Dan Andersson
2020-03-08 00:56:17

Richard Shapiro
2020-03-08 05:11:03

T.R. Griffith
2020-03-08 05:24:25

T.R. Griffith
2020-03-08 06:45:46

Stefan Giudici
2020-03-08 13:38:37

T.R. Griffith
2020-03-08 13:48:44

Stefan Giudici
2020-03-08 13:52:05

Dan Andersson
2020-03-08 14:16:21

Neil Ramsay
2020-03-08 22:49:44

原文網址 Andy Fox
2020-03-07 04:17:12

I've downloaded prusa slicer but now what? It looks like it preset with all the prusa slicer printers but I have a photon.
I mostly want to use it for the auto orientate function.

翻譯年糕

Jan Pfriender
2020-03-07 04:18:46

Omar Silva
2020-03-07 04:18:57

Michael Bradley-Robbins
2020-03-07 04:22:29

Andy Fox
2020-03-07 16:09:44

原文網址 Mark Wardle
2020-03-07 00:38:01

these are my support settings for the prusa slicer. i only use the slicer to add supports then export the stl with supports. this is for miniatures that are for printing directly on the build plate. they are ultra thin and leave hardly any marks and easy to remove. i gave the settings as pics so you know what you need to change. rather then just import my config file. hope this helps some of you. this is a tried and tested and works. i use auto then i clean them up manually.

翻譯年糕

Chris Koonce
2020-03-08 06:39:06

Mark Wardle
2020-03-08 06:44:45

原文網址 Alex Bainbridge
2020-03-04 23:08:16

Hollowing / Solid meshes.

I have a model that apparently is already hollow, but it's super thin so i'm concerned it won't print correctly. any way on how to fill it in so I can then re-hollow using mesh mixxer before putting into Prusa.. Can you hollow in Prusa?

翻譯年糕

Doug Bowman
2020-03-04 23:11:35

Alex Bainbridge
2020-03-04 23:12:44

Ken Schmitt
2020-03-04 23:14:26

Ken Schmitt
2020-03-04 23:14:50

Doug Bowman
2020-03-04 23:15:26

Derek Mears
2020-03-04 23:21:55

Alex Bainbridge
2020-03-05 01:29:00

Alex Bainbridge
2020-03-05 01:30:15

Alex Bainbridge
2020-03-05 01:32:18

Derek Mears
2020-03-05 02:13:05

Alex Bainbridge
2020-03-05 02:13:54

Derek Mears
2020-03-05 02:20:19

Derek Mears
2020-03-05 02:20:26

原文網址 Adam Michael Hennebeck
2020-03-04 11:17:11

All of these were printed using PrusaSlicer Orientation. The part of the base that was pointed down is flattened on each of these printed at different times. Thoughts?

LH-.05mm
Bottom Layer Count-8
Exposure Time: 10
Bottom Exposure Time: 90
Light Off Delay-1
Bottom Light Off Delay-3

AC Green. 20C

翻譯年糕

Adam Michael Hennebeck
2020-03-05 11:22:03

Adam Michael Hennebeck
2020-03-06 13:24:49

原文網址 Joe Papa Behre Behrend
2020-03-04 09:19:39

I heard that Prusaslicer is the best for autosupports (please correct me if I’m wrong). Does anyone happen to know the settings for the photon? I’m not sure if my support settings are good enough, the seem to leave damage (unless someone was a good setting for supports on chitubox). Any help would be fantastic!

我聽說prusaslicer最適合自動支援(如果我錯了請更正我). 有人碰巧知道光子的設定嗎? 我不確定我的支援設定是否足夠好, 似乎會造成損害(除非有人在chitubox上支援的好設定). 任何幫助都會很棒!

· 查看原文 · 為此翻譯評分

Rigo Arevalo
2020-03-04 09:20:37

Gregory Akin
2020-03-04 09:20:50

Joe Papa Behre Behrend
2020-03-04 09:21:16

Gregory Akin
2020-03-04 09:21:33

Gregory Akin
2020-03-04 09:21:37

全不選發文排行