Anycubic Photon Printer Owners 造訪社團 » LCD

Good evening guys, I have three questions to ask:
The first concerns the power of our LCD on the photo with a power of 405nM, 420 nM resins are not usable
I suppose I'm wrong?

Is there an update regarding software and LCD?

Have you ever heard of glass resin?
I mean an article that talks about this technology on dlp / sla technology that printed glass.

https://www.nature.com/articles/nature22061

Thank you all for your help

翻譯年糕

This photon clone has a better way to change the LCD screen. Anycubic should start looking at their clone competition :)

翻譯年糕

Another trick for new players.
I replaced the screen.
I thought I removed all the backing. I missed the last 2 sheets.
Becareful people when replacing the LCD.
Printing like new again.

翻譯年糕

Is it normal? I cannot get work my printer. I re adjusted Z axis, changed memory USB Stick, I upgraded firmware and I leveled the build platform many times but as you can see I cannot get good definition at 0.05 microns do you have any idea? Could you help me? I checked all connected rooms but everything is fine, I changed FEP film. I began to make calibration because in the last prints I'm loosing resolution and after the print finish some reason get stick into the VAT. i don't think that the issue is the LCD. Thanks

翻譯年糕

Fellows.
Need your advice.
Tried to print the monocure test stl.
Slicer shows correct slices.
As long the print is within the base rectangle all is ok. The first layer with the details and the lcd is shifting the front half .
Please see photos.
Any ideas?
Thank you

翻譯年糕

Any one have any idea where to get a replacement touch screen for the photon (the front input screen)..I managed to break mine in a spectacular act of stupidity / bad fortune and Fepshop are having no luck getting them in...and the official support site offered to send me the LCD projection screen *instead* and haven't replied since :) ?

翻譯年糕

LIGHTNING DEAL ENDS IN 4 hours
$415.20 for the photon!

ANYCUBIC Photon UV LCD 3D Printer Assembled Innovation with 2.8'' Smart Touch Color Screen Off-line Print 4.53"(L) x 2.56"(W) x 6.1"(H) Printing Size

ok fellow resineers, advice please.. got my photon yesterday, went through setup, everything good, did a print that MOSTLY came out ok, but I think the snarl on that was due to me not adding enough support. today however, I tried to print a new job, and on every single attempt (4) it's failed utterly... what's happening is the ENTIRE tray seems to be cured for the first mm or two... which obviously seems to stop the layers being cured as they should. the LCD does show the first layer correctly, so what on earth could be wrong

翻譯年糕

Hi folks. I would like to ask if anyone ever tried 3dm resins like 3DM-impact or 3DM-pro on a resin printer like photon/shuffle/wanhao etc. (From https://www.3dm-shop.com ) For my needs of small cases and functional parts most of resins are very brittle on thin walls and I need something stronger. I had also ordered printing my part by weerg.com from pa-12 nylon with SLS and it is something absolutely different. That material is very strong and does not break so easily as resin prints... Looks like those above 3DM resins are my last chance to get satisfying results on resin printer, however they cost fortune (165eur + 20%VAT w/o shipping for a 1kg bottle). I exchanged few emails with 3dp people and they confirmed that resin is compatible with lcd printers like photon etc, however on my question regards to the exposure times they say “We can recommend you the exposure times at 50 and 100 microns layer thickness at 0.5 mW/cm2 and also at 1.0 mW/cm2.”
Anyone can translate this into times??
Please whoever had tried these resins on any LCD printer, pls share your experience.

翻譯年糕

Hey guys! I have had my printer for about 6 months, and there have been no issues. Today when I went to print, I am getting a t:100 LCD error. When I try and run the UV detection, I am just getting two rows of lights vertically down the middle. I tried updating the firmware, but the issue is still there.

I have tried emailing support, but they advised me to update the firmware, and attach photos, something I did in the first email.

Any suggestions?

翻譯年糕