Anycubic Photon Printer Owners 造訪社團 » LCD

When replacing the photon lcd with the elegoo mars screen, does the connector go the same direction as you pull off the stock one? I have read some people put the connector on the wrong way and damaged their board

翻譯年糕

So what's the current "Best" firmware for the Original Photon? Half of my LCD "jitters" left/right during the exposure tests on 4.2.18?

EDIT: Seems solved after re-seating the connector, will be keeping an eye out for that in the future.

翻譯年糕

Is this a sign that my LCD screen is dying? It doesn't happen all the time but it seems to be every 50 layers or so. It should be exposing like it is in the first picture but every so often it glitches out. I tried different files on different USB sticks and it's the same thing.

翻譯年糕

Hey everyone!

So we have all seen the getshift.io LED array and it keeps popping up here every now and then but is there an LED array that can be used to upgrade the original photon?

I have noticed that I keep getting failed supports. I have changed the FEP and I don't think it's the LCD screen since it prints everything (even if it sticks to the FEP). I have to run my exposure times up to 15-16 secs when 12 should be the top end for a successful exposure. I'm wondering if it is the light source.

I am using Monocure Clear. Their batch control and quality is excellent. Also, the resin heater is keeping it around 27C.

Thanks!

翻譯年糕

Drivebelt....Elegloo Translucent Red & Monocure mix.... comes out Uber flexi!!!
? ? ?

(Will make note to ensure FEP screws are fully tightened next time... one came loose & now have pin hole in the FEP film which leaked stuff onto LCD during print...but screen was saved to fight another day.....phew!!!! ?‍♂️ ? )

Drivebelt.... elegloo半透明紅色和單治癒混合.... 出出uber flexi!!!
? ? ?

(將注意確保下次fep螺絲完全緊緊... 一個松開, 現在在fep影片中有一個洞, 在列印期間洩露東西到lcd... 但螢幕被儲存到另一天打架..... 呵呵 !!!! ♂️ ? )

· 查看原文 · 為此翻譯評分

Does anyone know how to fix this I replaced the lcd screen replaced lcd screen before it worked fine, firmware up to date no idea what to do so any suggestions or ideas would be great

翻譯年糕

Based on what I'm seeing it seems like my LCD screen is getting glitchy. It happens on the right side and it's happened with three different prints from two different usb sticks. And as I'm sitting here watching it run a print empty, every so often it does expose too much. You can see in the first picture of the screen what it is supposed to be printing but every once in awhile I get something like in the other pics of the screen. Since I've tried 3 different files on two different USB sticks I'm leaning towards the LCD screen going out.
Do you guys agree with me that that is probably an accurate assumption?
I kind of thought it would last a little bit longer since I've only had my printer since about the middle of December.
You guys think I'm right and thinking is the LCD screen going bad?

翻譯年糕

Hello group! I have a problem with my photon. First pic, printed in the midle of bed, second pic, on the closer side. In video, o see the shaking from the middle of lcd.
P. S. Sorry about my english and thanks for your advice.

翻譯年糕

A breeding pair. The one on the right is our works printer, my own is on the left. Had an interesting issue crop up with the works one, took a good print of it on Friday and set another away. Came back to it Monday morning to find nothing, no print, nothing stuck to the fep sheet. Thinking I’d cocked up the supports I bolstered them up, checked the level, filtered the resin and started again. Same result. This afternoon I tried an exposure test on it to find the whole lcd would illuminate at what appears to be half power, irrespective of which exposure mode was selected, re-updated the firmware (to the same version as it had received a fortnight ago), repeated the exposure and all was as it should be, ran my xyz test piece and it printed fine, so it’s back underway again now hoping that the issues are done with. I am puzzled as to what was the route cause, but at least I have some form of solution. Cheers

翻譯年糕

Hi all, thanks for the acceptance to the group.

So, I'm a total noob at the 3D lark but I bit the bullet and scored a Photon LCD which arrived today. Everything seems okay; UV Test appears fine, levelled the plate using the Flint Method etc. Can't do a Test Print yet as awaiting cleaning stock from eBay and the machine is @ -1000 C cos it's bloody cold out.

USB Stick was DOA. Well, the Photon saw it but the PC? It killed two of the USB slots on the PC but a reboot sorted that.

I have another USB stick that I've FAT32 formatted and D/L'ed then C&P'ed the Sticky Files (File_English_Photon.Rar - version 1) your page recommended into it.

Now, the Q's: From Anycubic.com I D/L'ed & installed "Workshop V2.1.20" and from the sticky I installed "Slicer64". What's the difference between the two? Are they the same sort of thing or what? Do either of them do what Tinkercad does?

I also note that my Photon is Firmware V4.2.17 - do I need to update it?

Thanks, Neal x

翻譯年糕