Anycubic Photon Printer Owners 造訪社團 » LCD

原文網址 Noorhisham Noordin
2019-09-15 12:14:40

Do i have to change the LCD?
If do, any recommendation where can i get cheap? ?

翻譯年糕

Russ Greene
2019-09-15 12:22:26

Noorhisham Noordin
2019-09-15 12:30:15

Noorhisham Noordin
2019-09-15 12:30:42

Russ Greene
2019-09-15 12:41:03

Noorhisham Noordin
2019-09-15 12:48:06

Bryan Mikolajewski
2019-09-15 13:16:40

Puren Bulat
2019-09-15 16:47:34

Johnny Wee
2019-09-16 19:14:25

Boon Kheng Tang
2019-09-16 20:58:41

Boon Kheng Tang
2019-09-16 21:01:00

Boon Kheng Tang
2019-09-16 21:01:08

原文網址 Robert Jeppesen
2019-09-14 22:11:09

This is what I get with the new firmware. I have tried photon 4.2.18, epax 4.2.18, and even the dreaded 4.2.19. I have used two different USB sticks and tried plugging USB in both before and after turning on the machine and loading the firmware. The result is always the first video with the flickering LCD. When I reverted to photon firmware 4.2.12 and got the second print video which looks like it should be fine, I am trying an actual test print now, but I am worried about frame shearing returning in the future.

翻譯年糕

Handrez Pintubola
2019-09-14 22:46:08

Gabriel Marian Alfons
2019-09-14 23:04:32

Patrick Samuel
2019-09-15 00:43:27

Robert Jeppesen
2019-09-15 02:00:26

Mata Mac Gille Fhionntain
2019-09-15 02:25:04

Kevin Boogaard
2019-09-15 04:43:03

Robert Jeppesen
2019-09-15 04:44:12

Joel Mendoza
2019-09-15 04:51:48

Robert Jeppesen
2019-09-15 06:46:35

Joel Mendoza
2019-09-15 07:03:22

Mata Mac Gille Fhionntain
2019-09-16 02:58:58

Juan Pablo Bagnon
2019-09-17 01:11:11

Robert Jeppesen
2019-09-17 05:32:34

原文網址 Zach J Hill
2019-09-14 13:45:56

I knew it was too good to be true, every print worked fine up to now, I think I’ve been luckier than some.

Does anyone know what would cause the FEP sheet to crease and deform like this? The top of the model (printed flat to the bed) has the same profile in it. Is the adhesion to the FEP too much? I’m using a Photon S with Wanhao Grey resin and settings from the Photonsters github document.

Fortunately for me the sheet didn’t rupture and leak resin onto the LCD.

Any advice appreciated, looks like I’ll be replacing the FEP sooner than expected. Has anyone used the Monocure FEP sheets on their photons? Monocure are a 20 minute drive from where I live so easy to get hold of.

翻譯年糕

Thean Osinski
2019-09-14 14:50:39

Zach J Hill
2019-09-14 14:52:48

Sean Croteau
2019-09-14 15:39:16

Zach J Hill
2019-09-14 16:11:26

原文網址 Chris Casarez
2019-09-14 10:34:28

I keep getting blobs in vat any idea if its time to replace the lcd cus i replaced the fep n still miss printing

翻譯年糕

Dave Smith
2019-09-14 10:41:39

Chris Casarez
2019-09-14 10:51:53

Arthur Withier
2019-09-14 19:54:39

Grant Weaver
2019-09-14 22:21:40

Nathanael Gardner
2019-09-15 09:43:22

Nathanael Gardner
2019-09-15 09:43:48

Chris Casarez
2019-09-15 09:57:35

原文網址 Jim Wolfe
2019-09-14 03:20:50

Hey All, I have a question i just started using ELEGOO ABS-Like 3D Printer Rapid Resin LCD UV-Curing Resin 405nm Standard Photopolymer Resin for LCD 3D Printing 1000Gram Grey off Amazon. After i soak it in 99% IPA for about 10 mins and then go over it with a soft toothbrush and re-dip a couple more time and go over it with the tooth brush again, then i have been curing it under a UV LED nail dryer for 20-30 mins. Is that the proper procedure? The Elegoo feels rubbery is that how it's suppose to feel? I like the detail and am happy with the outcome i just want to make sure i'd finishing the procedure? Thanks to all that can help me with this.

翻譯年糕

Melecio Guzman
2019-09-14 05:41:46

原文網址 Jason Nielson
2019-09-14 00:35:27

I need to replace my LCD on my photon. What should I be looking for? Where is the best place to buy?
Thanks

翻譯年糕

原文網址 George Collins
2019-09-13 20:20:40

Hi all- I keep getting the lcd error code: T88. So following online help I've downloaded the 'Firmware 4.2.18 from Anycubic' on the github website. I've copied these files onto the USB stick- but still getting the same issue- any help appreciated.

翻譯年糕

Melecio Guzman
2019-09-13 22:42:59

George Collins
2019-09-13 22:54:17

原文網址 Greg Kourakos
2019-09-13 11:13:01

Another really quick video which may help people on LCD screen failure:

翻譯年糕

原文網址 Daniel Gallagher
2019-09-13 08:14:38

So I received a replacement (presumably brand new) Photon from Amazon yesterday and the lcd seems to be failing after one successful print. I noticed something was wrong when the machine would continuously beep during the first layer and not move onto the second. The UV test (square) will illuminate momentarily before going out. Testing UV again with machine still on shows no UV square and only the blue lights beneath the lcd. Shutoff machine and retry and the test illuminates only momentarily, exhibiting the same behavior I'm thinking maybe a short in the lcd? I've opened up the machine to confirm the lcd cable is firmly attached to the board and tested on multiple firmware versions. Makes no difference. I'm guessing this is a failed lcd but figured i'd post up here to see if maybe i'm just missing something...

翻譯年糕

Tiernan Messmer
2019-09-13 08:20:06