Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Andrew Coen
2020-02-11 10:16:30

Thanks for the patience and advice community; just got one of the fiddliest bits I've ever done off the printer. Though it needs a bit more cleaning I just wanted to show off the fine wiring/hoses and how they came out!

翻譯年糕

Clifford Schwankner
2020-02-11 10:18:26

Alan Griffiths
2020-02-11 11:37:39

Andrew Coen
2020-02-11 20:36:23

原文網址 Andrew Coen
2019-12-31 20:40:22

gah.. thought I had figured it out (my first layers timer was set down to 30 secs, pushed it to 80) but this is what I got instead... there went a 27 hr print job.

翻譯年糕

Michael Power
2019-12-31 20:48:24

Paolo Maurini
2019-12-31 20:51:04

Jim Nelson
2019-12-31 20:52:27

Nathan Lange
2019-12-31 23:39:23

Andrew Coen
2020-01-01 00:12:57

Nathan Kopp
2020-01-01 03:50:43

Aaron Strome
2020-01-01 03:57:39

Bob Deblier
2020-01-01 04:10:42

Andrew Coen
2020-01-01 04:55:22

Andrew Coen
2020-01-01 04:56:05

Aaron Strome
2020-01-01 04:59:51

Aaron Strome
2020-01-01 04:59:55

Mike Fatchett
2020-01-01 08:26:11

Andrew Coen
2020-01-01 08:30:07

Andrew Coen
2020-01-01 08:30:31

Mark Pontius
2020-01-01 08:56:15

原文網址 Andrew Coen
2019-12-27 01:30:45

Ok, hivemine I need a hand. My bed is starting to become unleveled as it prints. I've cleaned all the components multiple times and the bed seems locked down well enough, but I guess some sort of suction is throwing the whole thing off. Been a different side the 3 times I've tried. Any other ideas on this sort of thing?

翻譯年糕

Joey Smith
2019-12-27 01:32:17

Alexander Bayerdorffer
2019-12-27 01:37:55

Alexander Bayerdorffer
2019-12-27 01:38:42

Ian Gill
2019-12-27 01:39:49

Andrew Coen
2019-12-27 02:45:10

Andrew Coen
2019-12-27 02:46:04

Matthew Auen
2019-12-27 04:31:22

Andrew Coen
2019-12-27 05:22:57

原文網址 Andrew Coen
2019-08-14 07:49:42

when folks are like "why'd you buy the 3d printer?"

You think 1:20th scale T-Rex heads are gonna appear at random for me? Nah I gotta print that stuff!

翻譯年糕

原文網址 Andrew Coen
2019-07-23 07:47:17

Thank you all for the help!! Managed to not only get it all zeroed in correctly but (and ignore the fact that I cut supports wrong) I did a 30mm figure test as well that came out great!

翻譯年糕

Susan Sioux Mercer
2019-07-23 09:06:59

Andrew Coen
2019-07-23 19:28:33

原文網址 Andrew Coen
2019-07-20 22:24:54

So 3rd try through (first bed wasn't set right, so complete failure, 2nd one was posted yesterday) and this time it come out better, but looking at the base, it feels like something went 'off' right from the go. did my bed become unleveled because of the suction perhaps? It seemed when I checked it that it was pulling pretty hard when it was printing, but I've only used FDM up until now so I have no gauge for 'normal'

almost dialed in, thanks for all the help so far all!

翻譯年糕

Sen Kun
2019-07-20 22:42:13

Bruce Barton
2019-07-20 23:29:29

Andrew Coen
2019-07-20 23:40:06

原文網址 Andrew Coen
2019-07-19 08:47:08

So first print failed as it didn't adhere to the baseplate (releveled and zeroed it) this time out it looks like it was doing great, but seems to have a few issues. Any tips?

翻譯年糕