Anycubic Photon Printer Owners 造訪社團 » USB

原文網址 Jonathon Michael Starwalt
2020-01-21 08:03:08

Here’s a fun troubleshoot for all of you wonderful, brilliant makers:

Two examples of a weird thing that’s happened to me a few times in the two weeks I’ve had my Photon.

On the paladin, you can see the one where the cape seemed to have jumped position part way before continuing to print as normal. On the barbarian’s hair, you can see where some part in the middle didn’t print.

Each one is next to a successful print, each of which were made with the exact same file, settings included, with the same resin. In both cases, the rest of the figure came out fine.

What could be the cause of these inconsistencies?

My photon shipped with firmware 4.2.17 and I have not updated it. Should I? I’m getting some good prints, some that are likely just support fails, and some weird stuff like this. Could it be a firmware issue?

I did switch the usb to a cheap but reliable sandisk one that I reformatted to FAT32 before using.

翻譯年糕

Hector Alvarez
2020-01-21 08:13:34

Jonathon Michael Starwalt
2020-01-21 08:34:40

Hector Alvarez
2020-01-21 08:42:29

Jonathon Michael Starwalt
2020-01-21 08:44:24

Hector Alvarez
2020-01-21 08:45:29

Jonathon Michael Starwalt
2020-01-21 08:47:27

Hector Alvarez
2020-01-21 08:48:42

Jonathon Michael Starwalt
2020-01-21 08:49:12

原文網址 Malcolm Robinson
2020-01-20 08:35:15

Greetings. Having had my Photon for a couple of month now, and having had successful prints and failed prints, I’m feeling a bit more confident and wanting to get the correct settings for my exposure rather than take defaults or work by trial and error. I’ve read the resin-xpfinder from GitHub and just want to make sure I have understood the instructions correctly. It looks like I have to change the config of the printer , print my resin test, and then return the printer to ‘print’ mode. Can u pls tell me if I have got this correct...

Step 1) load the file ‘test-mode.gcode’ onto the USB stick and run it (by selecting from the screen on the printer.
Step 2) run my exposure test file , resin-test-xxx from the USB stick
Step 3) Return the printer to print mode by running print-mode.gcode from the USB stick

Have I got this correct ?
Is there any chance my printer will not return to its present state when I bring it back to print mode ?

Thanks in advance

翻譯年糕

Susan Sioux Mercer
2020-01-20 09:30:07

Sander van Deijl
2020-01-20 17:36:43

原文網址 Christoph Czerny
2020-01-20 02:04:05

Hey, i have a Problem with my Printer. After closed a print, i changed the usb stick for a new Modell. Power was on.
This is the result, the printer didn't start.
I need your help.
Could it be i killed my board?

翻譯年糕

Lajos Olasz
2020-01-20 02:17:50

Ja No
2020-01-20 02:18:40

Lucas Parard
2020-01-20 02:19:19

Christoph Czerny
2020-01-20 02:22:29

Ja No
2020-01-20 02:25:15

Christoph Czerny
2020-01-20 02:26:19

Ja No
2020-01-20 02:37:13

Keith Yinger
2020-01-20 03:19:18

Stepan Stransky
2020-01-20 04:36:15

Bastian Dietert
2020-01-20 17:40:07

Christoph Czerny
2020-01-23 02:29:54

原文網址 Evan Garrison
2020-01-20 01:32:18

Can you usb from your laptop straight to printer or do you need flash drive

翻譯年糕

John Boyington
2020-01-20 01:38:13

Dustin Oliverius
2020-01-20 01:38:18

Liam Foltz
2020-01-20 01:43:48

Liam Foltz
2020-01-20 01:44:20

Stefan Giudici
2020-01-20 01:48:23

Benjamin Corcoran
2020-01-20 01:52:13

James Hendrix
2020-01-20 01:53:01

Evan Garrison
2020-01-20 01:55:56

Liam Foltz
2020-01-20 01:56:54

Benjamin Corcoran
2020-01-20 01:57:24

Scott Pavlich
2020-01-20 01:57:55

Benjamin Corcoran
2020-01-20 01:58:04

Evan Garrison
2020-01-20 01:58:06

Liam Foltz
2020-01-20 02:00:55

Liam Foltz
2020-01-20 02:01:34

Josh Shedaker
2020-01-20 02:20:07

Grant Weaver
2020-01-20 02:32:28

Evan Garrison
2020-01-20 02:38:27

Bob Deblier
2020-01-20 04:03:31

Evan Garrison
2020-01-20 04:43:35

Byron Taylor
2020-01-20 04:56:24

Smith Hayward
2020-01-20 22:56:13

原文網址 Gregory Akin
2020-01-19 23:13:18

Guys, is there a way for me to turn a 3d model of my WOW character into a printable file? What about someone else's? I want to make my guild leader her husband's character but I want to test it first. Her husband passed away last year.

翻譯年糕

Brett Isaacs
2020-01-19 23:14:51

Brett Isaacs
2020-01-19 23:15:58

Chris Thompson
2020-01-19 23:16:19

Gregory Akin
2020-01-19 23:18:26

Gregory Akin
2020-01-19 23:18:43

Markus Jorissen
2020-01-19 23:23:42

Stefan Giudici
2020-01-19 23:24:42

Gregory Akin
2020-01-19 23:29:57

John Aldred
2020-01-19 23:43:07

Tim Allen
2020-01-20 04:55:55

Jacob Palmer
2020-01-20 07:38:40

原文網址 George Jones
2020-01-19 22:00:58

My printer will no longer turn on. I put the USB into the Photon to perform a firmware update and the machine did its standard beeps (3, 2, 2) and then restarted but immediately started beeping again and the last beep got longer. This repeated until the last beep was just continuous. Now the tactile screen won't turn on at all. Adaptor has green light when plugged in so that part is atleast getting power. And the red light behind the z-axis still turns on.

翻譯年糕

原文網址 Logan Wholey
2020-01-19 09:44:22

New to the club, anyone else have any issues using a different USB drive than the one provided? The screen under print just shows 4 black squares where files/folders should be. TIA! New to the club, anyone else have any issues using a different USB drive than the one provided? The screen under print just shows 4 black squares where files/folders should be. TIA! 翻譯年糕

Angus Sanders
2020-01-19 09:45:51

Liam Foltz
2020-01-19 10:07:18

Robert Anthony Bekoscke
2020-01-19 10:09:54

Logan Wholey
2020-01-19 10:12:25

Logan Wholey
2020-01-19 10:14:32

Liam Foltz
2020-01-19 10:15:12

Logan Wholey
2020-01-19 10:18:51

Liam Foltz
2020-01-19 10:20:04

Liam Foltz
2020-01-19 10:20:32

Logan Wholey
2020-01-19 10:36:19

Aaron McCommon
2020-01-19 12:04:00

William Keller
2020-01-22 13:33:13

Logan Wholey
2020-01-22 18:53:21

原文網址 Stepan Stransky
2020-01-19 01:18:26

Thank you for accepting me into a group and next and now the first problem :-)

The new Photon installed this week, the new USB flash, UV display test does not show error, Anycubic green from the shipment. The first test print "cube" minor errors. Further printing interrupted printing of layers, the Z axis works without a problem. Now with OK calibration, the UV display no longer works - but OK /UV display test / is still displayed. I checked the UV display connection and it seems OK.

Control printing "cube" printed from USB flash manufacturer, other USB flash are new - it does not run from one USB flash - neither the original or new.

Where can there be a mistake?

翻譯年糕

原文網址 Travis Brock
2020-01-18 23:50:16

So i got my printer. Computer was way out dated to do anything. Spent almost a grand on a new computer. Printer wont read the usb stick to print something out -.- Im using chitubox to hollow/add supports and splice. Am i missing something?

翻譯年糕

Jeremy Babcock
2020-01-18 23:51:02

Travis Brock
2020-01-19 00:02:00

Daniel Quinn
2020-01-19 00:07:30

Travis Brock
2020-01-19 00:08:29

Sander van Deijl
2020-01-19 00:11:33

Travis Brock
2020-01-19 00:13:15

Jeremy Babcock
2020-01-19 00:13:48

Jeremy Babcock
2020-01-19 00:14:39

Travis Brock
2020-01-19 00:17:09

Branden Voss
2020-01-19 00:17:14

Travis Brock
2020-01-19 00:17:51

Will Koehler
2020-01-19 00:22:34

Travis Brock
2020-01-19 00:23:56

Will Koehler
2020-01-19 00:27:00

Travis Brock
2020-01-19 00:33:45

Will Koehler
2020-01-19 00:35:32

Will Koehler
2020-01-19 00:36:13

Will Koehler
2020-01-19 00:38:28

Travis Brock
2020-01-19 00:48:37

Mike Mchughes
2020-01-19 00:55:58

Travis Brock
2020-01-19 00:56:52

Will Koehler
2020-01-19 00:58:22

Travis Brock
2020-01-19 00:58:54

Alexander Bayerdorffer
2020-01-19 00:59:30

Travis Brock
2020-01-19 01:01:12

Alexander Bayerdorffer
2020-01-19 01:01:54

Travis Brock
2020-01-19 01:02:06

Justin Hardman
2020-01-19 01:18:03

Tom Calvin
2020-01-19 01:20:03

Travis Brock
2020-01-19 01:21:44

Travis Brock
2020-01-19 01:24:30

Alexander Bayerdorffer
2020-01-19 01:24:54

Alexander Bayerdorffer
2020-01-19 01:27:01

Travis Brock
2020-01-19 01:28:01

Felix Flauta Jr.
2020-01-19 01:29:31

Felix Flauta Jr.
2020-01-19 01:29:48

Travis Brock
2020-01-19 01:30:14

Felix Flauta Jr.
2020-01-19 01:30:29

Felix Flauta Jr.
2020-01-19 01:30:37

Felix Flauta Jr.
2020-01-19 01:31:18

Felix Flauta Jr.
2020-01-19 01:31:35

Felix Flauta Jr.
2020-01-19 01:32:02

Tom Calvin
2020-01-19 01:34:33

Travis Brock
2020-01-19 01:39:20

Travis Brock
2020-01-19 01:46:49

Mike Mchughes
2020-01-19 02:36:56

Travis Brock
2020-01-19 02:55:42

Jeremy Babcock
2020-01-19 04:21:38

Alexander Bayerdorffer
2020-01-19 04:22:25

Stefan Giudici
2020-01-19 05:26:28

Tim Moulton
2020-01-19 05:39:18

Felix Flauta Jr.
2020-01-19 05:59:24

Felix Flauta Jr.
2020-01-19 05:59:35

原文網址 Joschka Röben
2020-01-18 14:27:15

Grrr something keeps f*cking up my prints :( It should be four shallow cylinders with a supported latch to it. But after 1/3 of the cylinder height, the printer gos nuts. Any idea why? I used the same USB stick, I always do. Havent tried other models yet, but I have reformated the USB stick, cleaned the vat and releveled it. Also got a memory error of the end of a actually sucessfull print, but no error with the unsecessfully prints!

翻譯年糕

Shinagamei Cooley
2020-01-18 14:56:43

John MacDonald
2020-01-18 14:56:51

John MacDonald
2020-01-18 15:01:07

全不選發文排行