Anycubic Photon Printer Owners 造訪社團 » USB

原文網址 Jason Turner
2019-10-10 18:23:57

Recently, seemed to happen right after chitubox updated, my prints are stopping before they are finished and it exits out to the main screen. When I select the model i was attempting, it says "whether from the breakpoint to print". Anyone else get this? I thought it may be a bad USB drive, so I ordered another one. I re-formatted the stock one to see if that had something to do with it, but it did it to me again. Any thoughts?

翻譯年糕

Kris Occur
2019-10-10 18:54:27

Jason Turner
2019-10-10 18:57:36

原文網址 Oliver Stubley
2019-10-10 00:58:45

A few times now I have come back to a print that says it has finished, but the Z axis has stopped moving up mid print. What could cause this?

The z axis moves fine when I lift it back up afterwards. Not using the original USB, so don't think it's file corruption. Any ideas?

翻譯年糕

原文網址 Bryan Minelli
2019-10-09 19:10:42

So I had my first printer failure today. The part was still immersed in the vat halfway done while the printer said it was complete. No error code on the screen. I'm using stock USB key as I've had no issues so far.
Any ideas?
Corrupted file? Printer dying?

翻譯年糕

Savio Ku
2019-10-09 19:17:11

Bryan Minelli
2019-10-09 19:38:49

Savio Ku
2019-10-09 19:47:27

原文網址 Darren Juniper
2019-10-08 04:36:14

Hi all is there a maximum size usb stick that’s supported by the photon s?

I have tried a 64gb, 32gb and 4gb all formatted in fat32 but only 4gb one seems to work

翻譯年糕

Marnie Jefferson
2019-10-08 04:41:20

Darren Juniper
2019-10-08 04:44:12

Jeff Gowers
2019-10-08 04:54:25

Darren Juniper
2019-10-08 04:56:00

Jeff Gowers
2019-10-08 05:29:37

Simon Wilson
2019-10-08 05:40:52

Simon Wilson
2019-10-08 05:42:25

Darren Juniper
2019-10-08 06:26:54

Simon Wilson
2019-10-08 06:37:31

Marnie Jefferson
2019-10-08 06:45:19

原文網址 Alexis Claude
2019-10-07 19:26:58

Hello guys, I have a problem with my Photon s.
Yesterday I put a file to print on my usb key and since that, when I plug it on the printer, the screen remained frozen on the boot screen.
When I start without the usb key, it does work.
I have tried with an other usb key, but the printer don't recognize it.

Do you know this problem ?
Do you have a solution ?

Thank you a lot

翻譯年糕

Robb Nunya
2019-10-07 19:34:53

Alexis Claude
2019-10-07 19:38:52

Chad Elstad
2019-10-07 20:09:26

Alexis Claude
2019-10-08 00:39:00

原文網址 Patrick Keith
2019-10-07 04:04:36

I've tried several different USB drives and this is all I keep getting on the printer display in the Print menu. I have the default cube and my print file on the drive, both are .photon format.

翻譯年糕

Patrick Keith
2019-10-07 04:05:21

Jon Vogel
2019-10-07 04:07:28

Jennell Jaquays
2019-10-07 04:07:51

Jon Vogel
2019-10-07 04:08:39

Patrick Keith
2019-10-07 04:09:31

Patrick Keith
2019-10-07 04:11:06

Tim Moulton
2019-10-07 04:12:50

Velvet Mark
2019-10-07 04:14:01

Simon Wilson
2019-10-07 04:15:41

Patrick Keith
2019-10-07 04:16:10

Jennell Jaquays
2019-10-07 04:18:29

Patrick Keith
2019-10-07 04:18:58

Velvet Mark
2019-10-07 04:22:50

Velvet Mark
2019-10-07 04:24:17

Patrick Keith
2019-10-07 04:24:21

Tim Moulton
2019-10-07 04:24:33

Simon Wilson
2019-10-07 04:26:45

Patrick Keith
2019-10-07 04:26:49

Simon Wilson
2019-10-07 04:27:23

Patrick Keith
2019-10-07 04:31:51

Patrick Keith
2019-10-07 04:32:45

Patrick Keith
2019-10-07 04:33:08

Patrick Keith
2019-10-07 04:33:42

Simon Wilson
2019-10-07 04:34:45

Simon Wilson
2019-10-07 04:35:30

Patrick Keith
2019-10-07 04:37:19

Simon Wilson
2019-10-07 04:38:19

Patrick Keith
2019-10-07 04:39:47

Velvet Mark
2019-10-07 04:41:29

Velvet Mark
2019-10-07 04:42:25

Patrick Keith
2019-10-07 04:56:32

Sherri Johnson
2019-10-07 06:36:42

Patrick Keith
2019-10-07 06:38:41

Sherri Johnson
2019-10-07 06:49:50

Alex F-p
2019-10-07 14:59:39

Elle Heilig
2019-10-07 15:09:30

Patrick Keith
2019-10-07 19:28:50

Patrick Keith
2019-10-07 19:29:30

Peter Jarvie
2019-10-07 21:32:36

Jehú Paulín
2019-10-07 23:58:30

Patrick Keith
2019-10-08 01:15:49

Patrick Keith
2019-10-08 01:16:02

原文網址 Ian Jones
2019-10-05 03:36:31

I am trying to run the exposure calibration test from photonsters, but when I put the files onto the USB, the test-mode.gcode doesn't show up on the printer. The print-mode one does. Running FW 4.2.19. Anyone have any hints to point me in the right direction please?

翻譯年糕

Chris Cassaday
2019-10-05 03:38:50

Ian Jones
2019-10-05 03:40:51

Mario Hippmann
2019-10-05 03:49:23

Piotr Sych
2019-10-05 03:56:05

Ian Jones
2019-10-05 03:58:47

Piotr Sych
2019-10-05 04:01:16

Piotr Sych
2019-10-05 04:16:02

Ian Jones
2019-10-05 04:17:54

Piotr Sych
2019-10-05 04:21:38

Falcon Tom
2019-10-30 00:37:13

原文網址 Dan Cowan
2019-10-03 21:43:07

PLEASE HELP

Ok so i dont think its the file size anymore, my machine did print last night once i made the file smaller, but it was false hope i tried the same print again and i cannot get the machine past the first Layer without it shitting off and turning back on. I am beyond frustrated now with this printer. So far i have...

unplugged it and left it for a bit... worked once or twice

unplugged it with the power on (should drain all the memory) worked once or twice

did the factory reset, worked once for the next print

tried simple file names, 4 different usbs all freshly formatted

plugged directly into the wall on its own power outlet in case of not enough power.

flashed updated firmware...

Went through the phontonsters github troublshooting

I think thats all the trouble shooting but i cant get her to go this morning

when it prints it looks great.

翻譯年糕

Alex Vee
2019-10-03 21:47:56

Dan Cowan
2019-10-03 21:50:55

Alex Vee
2019-10-03 21:56:34

Dan Cowan
2019-10-03 21:58:14

Melecio Guzman
2019-10-03 22:00:44

Alex Vee
2019-10-03 22:02:20

Alex Vee
2019-10-03 22:03:44

Alex Vee
2019-10-03 22:04:39

Dan Cowan
2019-10-03 22:10:26

Melecio Guzman
2019-10-03 22:12:30

Dan Cowan
2019-10-03 22:15:55

Melecio Guzman
2019-10-03 22:25:30

Daniel Prows
2019-10-03 22:28:53

Alex Vee
2019-10-03 23:06:32

Daniel Prows
2019-10-04 00:12:49

Dan Cowan
2019-10-04 00:19:56

Dan Cowan
2019-10-04 00:30:20

Alex Vee
2019-10-04 01:29:18

Mike Syfritt
2019-10-04 01:57:07

Mike Syfritt
2019-10-04 01:57:56

Alex Vee
2019-10-04 02:08:21

Alex Vee
2019-10-04 02:09:47

Dan Cowan
2019-10-04 02:11:17

Dan Cowan
2019-10-04 02:11:33

Alex Vee
2019-10-04 02:11:35

Alex Vee
2019-10-04 02:11:41

Alex Vee
2019-10-04 02:11:55

Mike Syfritt
2019-10-04 02:12:37

Dan Cowan
2019-10-04 02:12:45

Dan Cowan
2019-10-04 02:12:50

Alex Vee
2019-10-04 02:13:30

Alex Vee
2019-10-04 02:13:39

Dan Cowan
2019-10-04 06:05:16

Alex Vee
2019-10-04 06:38:51

Alex Vee
2019-10-04 06:39:29

Alex Vee
2019-10-04 06:40:06

Dan Cowan
2019-10-04 06:45:19

Dan Cowan
2019-10-04 07:58:16

Dan Cowan
2019-10-04 07:58:46

Alex Vee
2019-10-04 08:08:53

Dan Cowan
2019-10-04 20:44:46

原文網址 Jeremy Weber
2019-10-02 21:43:04

The problems continue. So, I attempted my first large print last night. I was roughly 6" tall and was going to be a 7-hour print. I started it around 9:30pm and went to check on it a little after midnight. Printer was on but was no longer printing. The print bed was about an inch or so above the FEP where it had stopped printing.

The LCD screen was back to the home screen (system/tools/print). If I selected print, I could see the three photon files I have on my USB stick. The two I didn't print were not showing a preview and the file I was printing showed this icon and the filename was in red.

From what I can gather, it might be a poor USB drive. Does that sound right? What does this icon mean?

翻譯年糕

Nate Mueller
2019-10-02 21:51:26

Fred Bey
2019-10-02 21:52:09

Niall Forrester
2019-10-02 21:55:33

Jeremy Weber
2019-10-02 22:02:21

Fred Bey
2019-10-02 22:02:42

Jeremy Weber
2019-10-02 22:05:46

Sakis Goumenidis
2019-10-02 22:36:45

Jeremy Weber
2019-10-03 02:45:30

Milton Maxson
2019-10-03 04:35:23

Brett VanDyke
2019-10-03 04:37:29

原文網址 Matthew Tan
2019-10-01 17:40:17

Sorry for the long post.

I finally got my Photon S and tried to do my first two prints which both failed(Cube).

I'll post the pictures and try to maybe say what I think they could be. I don't have experience with 3D Printing and know I will only learn by doing and making the mistakes.

*** 1st Print ***
I think maybe what happened here was from me not shielding the printer from the sun well enough. It wasn't in direct sunlight but enough maybe bounced around and in.

Also when I was cleaning the FEP after this I noticed a really thin layer which I thought was resin but could be that protective layer that new FEP films come with.

When I first poured the resin I did shake it quite hard so there was quite a lot of bubbles so maybe a bubble in the wrong place?

*** 2nd Print ***
So this one almost came out right except for what you can see. Not too sure what happened here I covered the printer with the box it came with, But I did sneak a couple of peeks here and there.

I shook the bottle a bit less this time and there were still a bit of bubbles but not as much as the first time.

Not too sure what I could do. I just straight plugged in the USB and tried to print didn't tweak any settings. Maybe I need to level the bed again?

Thanks again everyone

翻譯年糕

Antonino Giambino
2019-10-01 18:20:21

Alex Clarke
2019-10-01 18:58:45

Alex Clarke
2019-10-01 19:00:24

Matthew Tan
2019-10-02 02:03:12

全不選發文排行