Anycubic Photon Printer Owners 造訪社團 » resin

原文網址 Mark Warren
2020-02-10 16:23:07

I had an accident - need assistance.

I was removing a print and accidentally tipped the entire printer over backward (I had no idea it was so unbalanced). Resin poured into the interior of the printer, flooded the back wall.

I had the presence of mind to keep it tipped back and most of the resin flooded into the back wall and out the bottom. It was messy, but it doesn't appear any got inside the screen or projector, and none got on the electronics that I can see.

It took a while to clean it up and everything appears to be working OK, except the printer will not home now. If you tell it to home, it goes up about 10mm and stops - no matter where you set home at. Everything else appears to work.

I'm thinking maybe resin may have gotten inside that sensor in the back, at the bottom behind the z-axis screw, but I can't tell.

Anyone have any idea what part might have been damage that would cause this behavior?

翻譯年糕

James Rooke
2020-02-10 16:27:39

Mark Warren
2020-02-10 16:28:38

原文網址 Michael Pollard
2020-02-10 15:40:33

So Valentines day is fast approaching.

Printed some things, Jewellery stand for earrings, rings and Necklaces. And some Keyrings.

Printed the keyrings on Ender3 and the hearts in clear red resin on PhotonS.

翻譯年糕

Michael Pollard
2020-02-10 15:47:31

原文網址 Henrik Andersen
2020-02-10 14:30:55

Trying to print Scale model wheels on my Photos S - file diameter is 25mm but prints come out at 26,28mm ....! Any ideas why and what to do ? Printning in anycubic trans green resin ...

翻譯年糕

Luke Pettit
2020-02-10 15:39:55

原文網址 Jason Edgel
2020-02-10 14:21:49

Once again failed test print, tried of cleaning this out and dumping back resin, anyone able to help me level/ calibrate, followed the instructions(I thought)

再次失敗的測試列印, 嘗試清理這個並扔回樹脂, 有人能幫助我水平/校准, 遵循指示(我想)

· 查看原文 · 為此翻譯評分

Brett Inglis
2020-02-10 14:24:32

Neil Forster
2020-02-10 14:24:48

Brett Inglis
2020-02-10 14:25:27

Justin Lincoln
2020-02-10 14:39:02

Sean Guna
2020-02-10 14:40:15

Jairo Ledesma
2020-02-10 14:48:41

Willie Randell
2020-02-10 15:00:02

Stefan Giudici
2020-02-10 15:35:21

Bruno Shepard
2020-02-10 15:44:52

Brett Inglis
2020-02-10 15:54:12

Brett Inglis
2020-02-10 15:58:21

Keif Davies
2020-02-10 16:20:51

Krunoslav Zlomislic
2020-02-10 16:48:31

Tom Sargison
2020-02-10 17:35:03

Paul West
2020-02-10 18:06:31

Brett Inglis
2020-02-10 20:08:48

Tom Sargison
2020-02-10 20:24:32

Tom Sargison
2020-02-10 20:25:29

David Scott
2020-02-10 20:25:49

Paul West
2020-02-10 20:47:14

Chris Thompson
2020-02-10 20:56:53

Hoghead Hoffer
2020-02-10 21:04:48

Pablo Rovira
2020-02-10 21:49:43

Rick Odland
2020-02-10 23:00:00

Jason Edgel
2020-02-10 23:13:47

Haydn Nelms
2020-02-11 00:20:59

Glenn Manser
2020-02-11 01:13:19

Rick Odland
2020-02-11 01:17:20

Jacob Hale
2020-02-11 04:37:54

Yurik Ueda
2020-02-11 05:50:44

Scott Coates
2020-02-11 06:06:11

Matthew King
2020-02-11 10:35:31

Fred Bey
2020-02-11 12:10:29

Daryl Allman
2020-02-11 14:11:30

Alessio Bernesco Làvore
2020-02-11 14:23:47

Tim Moulton
2020-02-11 14:42:50

Matt Reed
2020-02-12 00:32:18

Matt Reed
2020-02-12 00:32:29

Sam Cunningham
2020-02-12 02:36:44

Susan Sioux Mercer
2020-02-12 09:50:42

原文網址 Mike Warren
2020-02-10 13:51:02

So have been printing beautifully for months, even in my garage with cold temps, but recently the pieces are stuck to the plate, brittle, and pieces of the base are already chipping before I try to remove them? I lowered the exposure rate to 8 but the bases still broke when trying to remove?

Have leveled, tried different plates, bought new Elegoo Grey Resin. Running out of ideas.

翻譯年糕

Dallas Winston Fitzgerald
2020-02-10 13:55:57

Mike Warren
2020-02-10 14:00:09

Wes Mischke
2020-02-11 03:09:00

Wes Mischke
2020-02-11 03:10:31

原文網址 Olivia Nettles
2020-02-10 12:25:58

Test print is killing me with cute. Gonna need to make another test because I'm POSITIVE there's resin stuck in this just above the arms.

翻譯年糕

Kim Bourrie
2020-02-10 12:29:31

Olivia Nettles
2020-02-10 12:32:41

Olivia Nettles
2020-02-10 12:36:38

Austin Dickinson
2020-02-10 12:41:29

Jennifer Carter
2020-02-10 13:00:34

Htet Myat Thu
2020-02-10 15:07:33

Tibi Sucuturdean
2020-02-10 17:36:07

Olivia Nettles
2020-02-10 20:02:22

Kelly Rinaldi
2020-02-10 22:29:46

Marc Richards
2020-02-11 10:53:21

Kyle Telechan
2020-02-11 11:00:45

Kevin Smith
2020-02-11 11:07:07

Kyle Telechan
2020-02-11 11:18:11

Kevin Smith
2020-02-11 11:22:41

Olivia Nettles
2020-02-11 11:33:11

Gregory Akin
2020-02-11 11:36:04

Marc Richards
2020-02-11 11:48:02

原文網址 Michael McSpadden
2020-02-10 10:14:35

Just started printing, I was wondering if any one had any suggestions for economical resins. I mostly pint minis for table top games that I then paint. So color and finish are not much of an issue.

翻譯年糕

Harold Reavley
2020-02-10 10:23:49

Veda Toys
2020-02-10 10:25:44

Erik Morris
2020-02-10 10:45:31

David Sea
2020-02-10 11:28:15

Harold Reavley
2020-02-10 11:29:57

David Sea
2020-02-10 11:30:28

David Sea
2020-02-10 11:31:09

David Sea
2020-02-10 11:32:57

Harold Reavley
2020-02-10 11:33:03

David Sea
2020-02-10 11:33:37

Harold Reavley
2020-02-10 11:34:27

Harold Reavley
2020-02-10 11:36:38

Harold Reavley
2020-02-10 11:36:58

Bob Deblier
2020-02-10 16:48:45

Michael McSpadden
2020-02-10 22:48:18

Herman Simpson
2020-02-10 22:51:14

原文網址 Dustin Jorden
2020-02-10 10:11:34

Hello everyone new to resin printing. Just ordered my photon. Any suggestions to get started? Also best resin to buy? I am using this mostly to print DND minis.

翻譯年糕

Barthels Marvels
2020-02-10 10:23:26

Barthels Marvels
2020-02-10 10:23:44

Dustin Jorden
2020-02-10 10:25:17

Barthels Marvels
2020-02-10 11:17:38

Sander van Deijl
2020-02-10 17:22:41

Barthels Marvels
2020-02-10 21:47:09

Sander van Deijl
2020-02-10 21:48:22

原文網址 Olivia Nettles
2020-02-10 08:50:48

Attempting to print my baby Yoda. A bit concerned for a part. It might hold resin that isn't cured.

What should I do about it?

翻譯年糕

Tylr Dorchak
2020-02-10 08:52:48

Olivia Nettles
2020-02-10 08:55:49

Stefan Giudici
2020-02-10 09:14:48

Darren Donovan
2020-02-10 09:24:37

Peter Anderson
2020-02-10 12:30:01

原文網址 Scott Mitchell
2020-02-10 08:48:47

Third attempt at printing the Hero Forge paladin test file (resupported in Chitubox and validated). Print platform stayed in vat and did not move up the z axis for first 45% pf print. I stopped the print and raised the print platform and this was the result, a flat piece of resin handing off the platform. What's the issue now?

翻譯年糕