Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 David Sea
2020-03-15 02:10:14

I have a sliced file of huge bases with skulls. I followed the same procedure I always do, prusa for orientation and supports and repair, export to chitubox for hollowing and holes and slicing, photon for verification. For some reason, no matter which flash drive I use, when it hits the printer selection screen, the images disappear for everything beyond it in the file list and the printer can no longer read the files on the drive. Is there anyone willing to take my file and try it on their printer? Or is there something I'm missing? Never had this problem before.

翻譯年糕

原文網址 David Sea
2020-03-12 06:58:43

So, I've had to change 2 LCDs in under 2 weeks and I couldn't figure out why. Everything was leveled, resin strained every time, fep cleaned every time, etc.

I finally figured it out and wanted to let you guys know. I received some Siraya Fast grey resin that had some semi cured resin in it already, right out of the bottle. How did I figure this out? I strained the reain before it went into the vat and found it in the cleaned strainer.

Has anyone ever seen this?

翻譯年糕

Tobi Altebaeumer
2020-03-12 07:07:47

Jacob Hale
2020-03-12 07:28:22

David Sea
2020-03-12 07:33:41

David Sea
2020-03-12 07:34:13

Jacob Hale
2020-03-12 07:59:13

Keith Yinger
2020-03-12 23:19:04

David Sea
2020-03-12 23:23:57

David Sea
2020-03-12 23:25:15

Keith Yinger
2020-03-12 23:35:30

Justin Lincoln
2020-03-13 00:32:55

原文網址 David Sea
2020-02-17 07:32:23

This would be a marvelous print. Had anyone seen a file for this anywhere?

這將是一個很棒的印刷品. 有人在任何地方看到這個的檔案嗎?

· 查看原文 · 為此翻譯評分

Ben Wood
2020-02-17 07:34:24

Mark Cameron
2020-02-17 07:35:07

Scott Smith
2020-02-17 07:37:37

Lucas Battani
2020-02-17 07:40:36

David Sea
2020-02-17 07:41:29

Chantal Prijs
2020-02-17 07:42:20

Lucas Battani
2020-02-17 07:43:05

Mark Cameron
2020-02-17 07:45:02

Lucas Battani
2020-02-17 07:45:22

Mark Cameron
2020-02-17 07:50:56

David Sea
2020-02-17 07:56:01

Mark Cameron
2020-02-17 08:02:59

John Sparkman
2020-02-17 08:15:43

David Minford
2020-02-17 08:33:23

David Sea
2020-02-17 09:29:41

Sam Cunningham
2020-02-17 09:36:35

Alex Bale
2020-02-17 09:42:57

David Sea
2020-02-17 09:49:07

Clint Maiuri
2020-02-17 09:49:15

Matthew Eastman
2020-02-17 10:02:27

Connor DjGlargum Whitesell
2020-02-17 10:02:50

David Sea
2020-02-17 10:12:39

Drew Delano
2020-02-17 10:42:12

Drew Delano
2020-02-17 10:42:33

Jon Foster
2020-02-17 10:50:32

Lucas Battani
2020-02-17 12:02:18

Chris Christiansen
2020-02-17 13:18:06

Brian Jensen
2020-02-17 13:31:08

Drew Delano
2020-02-17 13:32:17

Mark Cameron
2020-02-17 16:10:53

Mark Cameron
2020-02-17 17:49:00

Mata Mac Gille Fhionntain
2020-02-18 05:28:52

Valerio Mariani
2020-02-18 05:36:46

Brandon Marcussen
2020-02-18 05:37:15

Valerio Mariani
2020-02-18 05:38:27

Valerio Mariani
2020-02-18 05:42:06

Tokage Hideto
2020-02-18 05:42:40

Noah Jefferson
2020-02-18 07:10:18

Lucas Battani
2020-02-19 09:24:47

原文網址 David Sea
2020-02-15 08:12:51

Anyone doing any scaffolding type supports? For example, if I wanted to print a ton of 1" crates, instead of just printing what fits on the bed, using more of the Z axis during one print and stacking them up. I'd love to hear your thoughts and best practices.

翻譯年糕

Derek Reihe
2020-02-15 08:13:12

Robert Schulman
2020-02-15 11:11:26

原文網址 David Sea
2020-02-12 11:28:45

My last 2 prints have holes running vertically through the entire print of varying sizes. Any idea what might cause this? If you look closely at the image, you can see them. They are NOT drain holes that I put in. They were from separate flash drives. I use prusa for auto supports and added lots and lots of extra supports to this one. I use chitubox to slice. Temperature is fine. No visible scarring on the FEP.

翻譯年糕

Harold Crossley
2020-02-12 11:33:44

Priscilla Holloway
2020-02-12 11:34:58

Jason Dickson
2020-02-12 11:35:31

Scott Clark
2020-02-12 11:36:28

Matthew King
2020-02-12 11:37:07

Tauri Icenogle
2020-02-12 11:43:05

Tony Moura
2020-02-12 11:43:48

Natasha Kerensky
2020-02-12 11:58:51

David Sea
2020-02-12 11:59:55

Natasha Kerensky
2020-02-12 12:00:25

Natasha Kerensky
2020-02-12 12:00:32

Natasha Kerensky
2020-02-12 12:02:20

Natasha Kerensky
2020-02-12 12:02:55

Paul West
2020-02-12 12:06:20

Herman Simpson
2020-02-12 12:32:25

Steve Filpansick
2020-02-12 13:16:56

Stefan Giudici
2020-02-12 13:57:56

Susan Sioux Mercer
2020-02-12 14:44:36

Damjan Ketükil
2020-02-12 20:24:10

Elliot McAllister
2020-02-12 22:30:32

David Sea
2020-02-12 22:49:16

原文網址 David Sea
2020-02-05 02:52:36

Resolved: I cannot use gcode files with the Fauxton. =/

I am attempting to run the resin exposure finder. I downloaded it from Github. I have a standard Photon running Firmware V5.0.2. When I put the GCODE files in the base directory (as pictured) the printer cannot see the files to print. I feel like I'm missing something obvious, because the directions make it seem obvious. I should just be able to insert the flash drive and print the GCODE files, right?

翻譯年糕

David Sea
2020-02-05 02:53:19

David Sea
2020-02-05 03:03:36

Jim Monaco
2020-02-05 03:04:25

David Sea
2020-02-05 03:05:37

Jim Monaco
2020-02-05 03:09:14

Victor Organek
2020-02-05 03:09:48

David Sea
2020-02-05 03:11:53

David Sea
2020-02-05 03:12:37

Victor Organek
2020-02-05 03:14:17

Jim Monaco
2020-02-05 03:14:19

David Sea
2020-02-05 03:15:12

Sen Kun
2020-02-05 03:33:58

David Sea
2020-02-05 03:36:56

Sen Kun
2020-02-05 03:37:25

David Sea
2020-02-05 03:37:27

Sen Kun
2020-02-05 03:37:53

Jim Monaco
2020-02-05 03:39:20

Sen Kun
2020-02-05 03:40:36

David Sea
2020-02-05 03:41:08

原文網址 David Sea
2020-02-05 01:30:25

I've been having problems since changing my FEP and resin from Elegoo grey to Anycubic green. I've leveled and releveled. The FEP is drum tight. I changed from the flash drive that came with it to another, which resolved some issues. My settings are per the spreadsheet, but I haven't plugged in to a network to run the resin test, so I haven't put the printer into test mode yet. This is the print I am getting. It is supposed to be kobold miniatures at 45 degrees, on a raft and supports as all the videos taught. The arms and weapons are coming out flattened. The models are falling off and sticking to the FEP.

翻譯年糕

Andrés Seoane
2020-02-05 01:34:25

Derek Reihe
2020-02-05 01:35:17

David Sea
2020-02-05 01:46:55

David Sea
2020-02-05 01:48:10

Philippe Maegerman
2020-02-05 01:48:29

David Sea
2020-02-05 01:48:46

David Sea
2020-02-05 01:50:04

Philippe Maegerman
2020-02-05 01:50:13

David Sea
2020-02-05 01:50:55

Philippe Maegerman
2020-02-05 01:51:19

David Sea
2020-02-05 01:51:51

David Sea
2020-02-05 01:52:04

Philippe Maegerman
2020-02-05 01:52:06

Philippe Maegerman
2020-02-05 01:52:20

Philippe Maegerman
2020-02-05 01:52:42

David Sea
2020-02-05 01:53:27

David Sea
2020-02-05 01:53:39

Philippe Maegerman
2020-02-05 01:53:48

Philippe Maegerman
2020-02-05 01:53:59

David Sea
2020-02-05 01:54:03

Philippe Maegerman
2020-02-05 01:54:21

David Sea
2020-02-05 01:55:10

Philippe Maegerman
2020-02-05 01:55:40

David Sea
2020-02-05 02:40:57

Jeff Surma Jr.
2020-02-05 03:16:01

Jeff Surma Jr.
2020-02-05 03:18:02

Derek Reihe
2020-02-05 03:27:40

Justin Lincoln
2020-02-05 06:37:10

Justin Lincoln
2020-02-05 06:38:51

原文網址 David Sea
2020-02-04 09:24:31

Ok, I've been struggling with getting anything to print. I'm getting shearing, flattened arms, some items finishing and not others. This image is just a basic bunch of bases for miniatures. Some printed. Some cut off. I am leveled properly. Is this a case of maybe a bad flash drive? Im using the one that came with the printer, which I've heard here can be problematic.

翻譯年糕

Justin Lincoln
2020-02-04 09:26:27

Travis McGeathy
2020-02-04 09:26:46

David Sea
2020-02-04 09:30:58

David Sea
2020-02-04 09:32:36

Will Koone
2020-02-04 09:34:35

Kyle Telechan
2020-02-04 10:10:18

Vincent Balmont
2020-02-04 10:52:08

David Sea
2020-02-04 21:54:21

原文網址 David Sea
2020-01-30 01:27:48

First time posting. I ended up with a hole in my FEP and took it apart. My LCD got resin cured on it. I am pretty proud of the cleaning job I did and it looks perfect. I have new FEP's coming in tomorrow. Is there anything I need to think about, such as the possibility of resin leaking through the cracks between the LCD and the printer?

翻譯年糕