• 3D列印服務
  • #maker+t=market
  • COSPLAY 3D 建模
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » resin

原文網址 Carla Birch
2020-02-09 15:49:29

So I see this happing more and more lately, so when helping a new user with resin settings please keep in mind to check if they have the Photon or Photon S.

Because I keep seeing people telling people there settings they use (clearly photon settings) when the user as a Photon S. Exp times are much lower than the Photon eg grey on photon is more 80 bottom and 11 normal, on the S it’s more 30 bottom and 6 normal.

So the advise is normal only going burn the LED out faster then it should but you going give very overexposed prints or by ramping up the bottom time you might be getting a print to stick for them but the high bottom time is hiding the fact they have another problem like the FEP needs to have more tension or the level is not fully right.

So please don’t just drop photon exp times or the photon google doc to people needing help with a Photon S.

翻譯年糕

Niall Forrester
2020-02-09 16:57:01

Carla Birch
2020-02-09 16:59:17

Oksana Shevchenko
2020-02-09 18:16:30

Niall Forrester
2020-02-09 19:16:41

AusRob Kirgan
2020-02-09 19:23:00

Scott Pavlich
2020-02-09 22:19:59


原文網址 Daniel Reeder
2020-02-09 13:49:00

Hey friends!

I got a Photon S last week and I've tried to print three things and none of them have seated to the bed. Could you share tutorials, settings, what resins, etc to use? I tried releveling my bed but honestly, I am lost at the moment.

翻譯年糕

Matthew Steeghs
2020-02-09 13:50:19

Daniel Reeder
2020-02-09 13:52:44

Matthew Steeghs
2020-02-09 13:53:47

Daniel Reeder
2020-02-09 13:54:05

Devin McClellan
2020-02-09 13:54:26

Matthew Steeghs
2020-02-09 13:54:37

Daniel Reeder
2020-02-09 13:58:02

Matthew Steeghs
2020-02-09 13:58:23

Daniel Reeder
2020-02-09 14:03:41

Daniel Reeder
2020-02-09 14:04:21

Daniel Reeder
2020-02-09 14:04:58

Andrew Smith
2020-02-09 14:05:55

Daniel Reeder
2020-02-09 14:06:21

Andrew Smith
2020-02-09 14:06:40

Matthew Steeghs
2020-02-09 14:07:09

Daniel Reeder
2020-02-09 14:07:10

Andrew Smith
2020-02-09 14:07:27

Daniel Reeder
2020-02-09 14:07:56

Daniel Reeder
2020-02-09 14:09:42

Matthew Steeghs
2020-02-09 14:18:31

Sander van Deijl
2020-02-09 14:26:47

Matthew Steeghs
2020-02-09 14:33:54

Carla Birch
2020-02-09 15:36:22

Carla Birch
2020-02-09 15:38:29

Sander van Deijl
2020-02-09 16:11:53

Matthew Steeghs
2020-02-09 16:18:42

Daniel Reeder
2020-02-09 18:21:38

Carla Birch
2020-02-09 18:24:41

Daniel Reeder
2020-02-10 06:23:46

Paul 'Jam' Morris
2020-02-10 06:37:56

Daniel Reeder
2020-02-10 06:39:24

Paul 'Jam' Morris
2020-02-10 06:41:01

Daniel Reeder
2020-02-10 07:35:13

Daniel Reeder
2020-02-10 11:25:11


原文網址 Vincent Balmont
2020-02-09 11:38:58

First bottle of resin finally ran out.

翻譯年糕

Clark Paints
2020-02-09 11:53:02

Vincent Balmont
2020-02-09 12:02:10

Justin White
2020-02-09 12:04:54

Vincent Balmont
2020-02-09 12:11:48

Justin White
2020-02-09 12:12:37

Michael Ray
2020-02-09 12:38:36

Vincent Balmont
2020-02-09 12:42:39

Michael Ray
2020-02-09 12:45:30

Vincent Balmont
2020-02-09 12:50:39

Myranda Laurel
2020-02-09 13:16:56

Vincent Balmont
2020-02-09 13:26:09

Vincent Balmont
2020-02-09 13:35:13

Myranda Laurel
2020-02-09 13:38:04

David Harris
2020-02-09 14:24:36

Vincent Balmont
2020-02-09 14:44:44

David Harris
2020-02-09 15:00:37

Joey Smith
2020-02-09 15:13:01

Clark Paints
2020-02-09 15:43:44

Vincent Balmont
2020-02-09 15:52:53

Vincent Balmont
2020-02-09 15:55:18

Gilles Miguel
2020-02-09 22:23:42

Joey Smith
2020-02-09 22:49:35

Josh Hawkins
2020-02-10 00:18:40

Justin White
2020-02-10 00:19:11

Vincent Balmont
2020-02-10 00:21:45

Justin White
2020-02-10 00:22:38

Josh Hawkins
2020-02-10 00:23:02

Vincent Balmont
2020-02-10 00:24:21

Justin White
2020-02-10 00:28:13

Vincent Balmont
2020-02-10 00:30:03

Justin White
2020-02-10 00:30:28

Vincent Balmont
2020-02-10 00:32:25

Justin White
2020-02-10 00:33:04

Ken Van De Sompel
2020-02-10 02:23:01

Mark Daniel Bandilla
2020-02-10 05:29:42

Michael Ray
2020-02-10 06:40:03

Vincent Balmont
2020-02-10 07:08:13

Vincent Balmont
2020-02-10 07:08:25

Vincent Balmont
2020-02-10 07:08:27

Vincent Balmont
2020-02-10 07:08:32

Vincent Balmont
2020-02-10 07:08:37

Vincent Balmont
2020-02-10 07:08:41

Vincent Balmont
2020-02-10 07:08:48

Vincent Balmont
2020-02-10 07:10:34

Vincent Balmont
2020-02-10 07:10:44

Vincent Balmont
2020-02-10 07:10:55

John Sparkman
2020-02-10 07:26:02

Peter Anderson
2020-02-10 12:29:06

Vincent Balmont
2020-02-10 12:48:40

Mark Daniel Bandilla
2020-02-11 02:22:35

Vincent Balmont
2020-02-11 05:57:59

Mark Daniel Bandilla
2020-02-22 05:27:52

Vincent Balmont
2020-02-22 05:53:55


原文網址 Denlee Paddy Rhodes
2020-02-09 10:01:37

Remember kids, make sure you've got enough resin in the vat to finish the job!

記住孩子們, 確保你在增值稅中有足夠的樹脂來完成這項工作!

· 查看原文 · 為此翻譯評分

Matty Bulmer
2020-02-09 10:07:50

Jason Dunham
2020-02-09 10:10:08

Denlee Paddy Rhodes
2020-02-09 10:10:11

Denlee Paddy Rhodes
2020-02-09 10:10:40

Aj Foraker
2020-02-09 10:18:09

Denlee Paddy Rhodes
2020-02-09 10:19:09

Denlee Paddy Rhodes
2020-02-09 10:19:40

Aj Foraker
2020-02-09 10:20:29

Denlee Paddy Rhodes
2020-02-09 10:20:53

Denlee Paddy Rhodes
2020-02-09 10:21:42

Aj Foraker
2020-02-09 10:21:59

Denlee Paddy Rhodes
2020-02-09 10:24:58

Denlee Paddy Rhodes
2020-02-09 10:27:50

Matty Bulmer
2020-02-09 14:57:16

Denlee Paddy Rhodes
2020-02-09 16:49:05

Sander van Deijl
2020-02-09 18:46:00

Matty Bulmer
2020-02-09 19:10:23

Denlee Paddy Rhodes
2020-02-09 19:11:52


原文網址 Wilbur Long
2020-02-09 08:41:53

PROBLEM SOLVED. THANKS!

I have uploaded 2 screen shots to illustrate my problem. I hope you can help me.

I have designed part of a building in Blender. It consists of 4 walls with siding, windows and a door. One of the screen shots shows it as it appears in Blender. You can see that it has no ceiling or floor, just the walls. I export it as an STL file.

The next screen shot is from Chitubox, showing the imported STL file after I added supports for printing. All is well at this point. No ceiling, no floor. I slice it and export it as a .photon file, and the File Validator says "Whoopee."

Then I print the photon file and get a print that has a solid ceiling and floor, which traps a load of resin.

I have gone back to the File Validator and close inspection shows a 16-layer ceiling and a 16-layer floor, which is invisible in Blender or Chitibox. Is their a way to prevent this, short of using the File validator to delete the ceiling and floor, pixel by pixel?

翻譯年糕

Luiz Junior
2020-02-09 08:53:43

Chris Thiessen
2020-02-09 08:57:39

Chris Beaumont
2020-02-09 08:59:11

Wilbur Long
2020-02-09 09:21:09

Wilbur Long
2020-02-09 09:22:47

Wilbur Long
2020-02-09 09:24:57

Brendon McDonough
2020-02-09 09:43:10

Wilbur Long
2020-02-09 09:55:33

Wilbur Long
2020-02-09 09:57:31

Richard Humble
2020-02-09 14:09:17

Wilbur Long
2020-02-09 22:18:55

Ryan Champion
2020-02-10 01:49:40

Anthony Fennell
2020-02-10 02:01:33

Wilbur Long
2020-02-10 05:36:47


原文網址 Michael Pescuma
2020-02-09 08:13:32

OK I've had no problem running the exposure test in the past, but I just ran it at 30micron with Dragon Grey resin... and this is what I got. Kinda... not working lol. Any ideas what I could adjust or what I could fix to get it to come out?

翻譯年糕

Chris Rees
2020-02-09 09:19:37

Michael Pescuma
2020-02-09 09:20:39

Pierre Eichel
2020-02-09 20:54:57

Michael Pescuma
2020-02-09 22:34:44

Pierre Eichel
2020-02-09 22:41:32

Michael Pescuma
2020-02-09 22:42:25

Pierre Eichel
2020-02-10 03:13:44


原文網址 Mono MonochromeAgent
2020-02-09 07:31:42

Requesting some input!
The problem:
Anycubic Skin refuses to adhere to the buildplate.
It just gets cured to the bottom of the vat on the FEP.
Dragon Resin Grey is adhering and printing successfully without issue. Anycubic Skin will not, regardless of exposure settings.

Troubleshooting:
- FEP was replaced several prints ago - prints remained successful afterwards when printing in Grey resin.
- I have tried several different exposure settings and 2 different objects. Skin Always fails.
- I have re-leveled the build plate.
- Printed the same test objects, using my Dragon Resin (Grey), with success The Grey adheres to the print bed without issue. The Anycubic Skin does not.
-Temperature of the room is maintained using a space heater between 60-75 degrees
- Resin is stored in a comfortable indoor temperature (72 degrees)
- Resin is always shaken before pouring

Test Object:
- Test object is a flat disk-like pendant that is printed flat against the build plate. this test object has printed successfully numerous times in two other types of resin.
- I have also printed other objects with success in grey, that skin fails. I have yet to have a single successful print in Skin.
My thoughts:
> I do not think this is a leveling issue.
> My only conclusion is, do I have a bad bottle of resin?
> Anycubic Skin was purchased via Amazon
> Anycubic Skin has a lot of bubbles after shaking, but it's less viscous than Dragon Resin so it may not indicate any problem but I'll mention it anyways.
Successful Grey print settings (A little overexposed but at least it adhered)but Trying the same in Skin yielded no success.
Normal Exposure: 15sec
Offtime: 7 sec
Base Exposure: 70sec
Base Layers: 8

Failed Skin settings:
Normal Exposure: 5sec
Offtime: 2sec
Base Exposure: 50sec
Base Layers: 8sec

請求一些意見!
問題:
Anycubic面板拒絕遵守建築板.
它剛剛被治癒到fep上的增值稅底部.
龍樹脂灰色成功地堅持和列印, 沒有問題. 任何cubic面板不會, 不管曝光設定.

煩惱:
- fep在幾張列印之前被更換-之後印刷灰色樹脂時, 列印仍然很成功.
-我嘗試了幾個不同的曝光設定和2個不同的物體. 面板總是失敗.
-我重新調整了建造盤子.
-用我的龍樹脂(灰色)列印同樣的測試物件, 成功, 灰色堅持在列印床上. Anycubic面板沒有.
-房間的溫度是使用60-75度之間的空間加熱器保持.
-樹脂儲存在舒適的室內溫度(72度)
-樹脂在傾盆前總是動搖

測試物件:
-測試物件是一個平盤一樣的吊墜, 列印平板. 這個測試物件已經成功地印刷了另外兩種樹脂.
-我也印刷了其他在灰色中成功的物體, 面板失敗了. 我還沒有一個成功的面板列印.

我的想法:
>我不認為這是一個平凡的問題.
>我唯一的結論是, 我有一瓶樹脂嗎?
> anycubic面板是通過亞馬遜購買的
> anycubic面板在搖晃後有很多泡泡, 但它比龍樹脂少, 所以它可能不會顯示任何問題, 但無論如何我會提到它.

成功的灰色列印設定(有點過量, 但至少它堅持), 但在面板嘗試同樣的嘗試沒有成功.
正常曝光: 15秒
時間: 7秒
基底曝光: 70秒
底層: 8

面板設定失敗:
正常曝光: 5秒
時間: 2秒
基底曝光: 50秒
底層: 8秒

· 查看原文 · 為此翻譯評分

Matt Hooton
2020-02-09 07:40:06

Mono MonochromeAgent
2020-02-09 07:40:45

Sokha Ang
2020-02-09 07:41:33

Matt Hooton
2020-02-09 07:42:00

Mono MonochromeAgent
2020-02-09 07:42:13

Matthew James Gaither
2020-02-09 07:56:41

Matthew James Gaither
2020-02-09 07:57:03

Matthew James Gaither
2020-02-09 07:57:13

Mono MonochromeAgent
2020-02-09 07:58:16

Matthew James Gaither
2020-02-09 08:08:15

Mono MonochromeAgent
2020-02-09 09:05:21

Mono MonochromeAgent
2020-02-09 15:27:58

Mono MonochromeAgent
2020-02-09 15:28:17


原文網址 Simon Dyer
2020-02-09 06:13:39

Cracks! I’ve been printing a few of these as I improve the design then suddenly this one has several cracks like you can see. What did I do wrong? Too much fan, too long in the IPA, old resin???

翻譯年糕

Sean Bauer
2020-02-09 07:08:30

Richard Humble
2020-02-09 07:09:53

Simon Dyer
2020-02-09 14:58:50


原文網址 Ariel Cabahug
2020-02-09 06:08:46

Hello, I need help. My prints have been failing.

My very first print was a success, but the bottom was half-off the BP once it was done. My second print been a disaster in three attempts.

First attempt resulted in the print separating from the BP and falling into the Vat. Removed the failed print, chalked it up to weak base, added more supports, cleaned BP, and printed again.

The second attempt was worse. It never stuck to the build plate. Removed failed print, returned resin to bottle, cleaned up vat and BP, Levelled BP and rezeroed, reapplied resin to vat.

Same issue with the third print. At this point, I’m just scratching my head and wondering why my recent prints aren’t working.

Bottom exposure time is 80s and normal exposure time is 10s. Printer is located in the basement and the window is open to let out the smell, although it’s chilly b/c of Canadian winters. Resin is Nova3D Resin.

翻譯年糕

Stefan Giudici
2020-02-09 06:25:02

Oksana Shevchenko
2020-02-09 06:27:12

Ariel Cabahug
2020-02-09 07:37:30

Ariel Cabahug
2020-02-09 07:37:38

Sander van Deijl
2020-02-10 19:27:13


原文網址 Jim Nelson
2020-02-09 05:22:59

My rant for the day-- I love my Photon S, but whoever designed that cockamamie connector for the LCD screen-- held together with tape, no less-- should be boiled in resin and pickled in IPA!

翻譯年糕


 

全不選 發文排行