Anycubic Photon Printer Owners 造訪社團 » resin

Did my first print on eryone's clear resin. Gorgeous. Printed very well with no issues that I can see from pre cure. 0.02 mm at 9 seconds. Probably could drop to 8 but eh

我在eryone的清樹脂上做了我的第一個印. 華麗. 列印得很好, 沒有我從預治療中看到的問題. 9秒0.02 mm. 可能會降到8, 但呃

· 查看原文 · 為此翻譯評分

Anyone adding Mica powders to the resin for artistic effect? Does it work well? Does it damage the printer in any way?

翻譯年糕

OK, a question for those using Ultrasonic cleaners and Simple Green. How do you go about cleaning the resin left over in the cleaner and how often to do you do it? I was thinking I would empty the simple green into a large clear tupperware container, and put it out in the sun to cure the resin (much how I did with IPA) and was wondering if that was the best practice for this kind of cleaner.

So far I have LOVED using Simple Green with the Ultrasonic. Just want to make sure I'm cleaning/managing it right.

好的, 問那些使用超聲波清潔劑和簡單綠色的問題. 你怎麼清理留在清潔工的樹脂, 你多久做一次? 我在想, 我會把簡單的綠色清空到一個大清澈的tupperware容器里, 然後把它放出來治癒樹脂(我如何處理ipa), 並想知道這是不是這種清潔的最佳做法.

到目前為止, 我喜歡使用簡單的綠色與超聲波. 只是想確認我打掃/管理正確.

· 查看原文 · 為此翻譯評分

Removing a small blob of harden resin on LCD screen.

翻譯年糕

So, looking into resin, as this is my first printer.

I saw some are cheaper than anycubic resin, does it have the same outcome or is there a difference?

Photon S is what I have, started with the translucent green that came with it.

翻譯年糕

So..... My 1/7 Bell 206 cockpit - I designed, and 3d printing...
Wait for it.... I initally started doing this with resin BUT multipart-functional assembly I was struggling with shrinkage and dimensional accuracy (even when using SirayaTech)

So..... went back to FDM and switched the nozzle to 0.15 and layer height 0.05mm - printed with Prusament ASA and Extrudr PLA NX2.

YES YES....I know, it's not Photon.
But point is, I started my printing journey with resin and kind of ended up stuck in the dogma - any small detailed prints, USE resin.
It's nice to see you can really push the limits of printing on FDM and get amazing detail as well - minimum loss of fidelity! And benefit it - parts are lighter and stronger :)

Moral of the story, be pragmatic :D

所以..... 我的1/7 bell 206駕駛艙-我設計, 3 d列印...
等等.... 我initally開始用樹脂做這個, 但多功能組裝, 我正在努力使用縮水和維度(即使使用sirayatech)

所以..... 回到fdm, 把噴嘴換成0.15和0.05毫米-用prusament asa和extrudr pla nx2列印.

是的, 是的.... 我知道, 這不是光子.
但重點是, 我用樹脂開始了我的印刷之旅, 最後卡在教條中-任何小細節印花, 使用樹脂.
很高興看到你真的可以在fdm上推動印刷的極限, 並獲得驚人的細節-最低程度地失去忠誠! 並受益-零件更輕, 更強大 :)

故事的道德, 要務實 :D

· 查看原文 · 為此翻譯評分

guys, any idea what could be reason?
i have already printed some parts on this settings, now having issue
anycubic black, 0,04/9sec, part is 40.2deg tilt.
wall thickness 2mm
dead pixels? resin cured to fep blocking light go through?

翻譯年糕

Correct me if I'm wrong, but resin test is a good way to double check level as well

如果我錯了, 請糾正我, 但樹脂測試也是雙重檢查水平的好方法

· 查看原文 · 為此翻譯評分

Any thoughts on using resin from a different company. Im a dentist who is trying to use a biocompatible resin from a different company because anycubic doesn't have one?? Thanks

翻譯年糕

Washable resin printing.

Rinse with water. It's so simple.

翻譯年糕