Anycubic Photon Printer Owners 造訪社團 » thingiverse

Alright. Been a while since I needed help. Struggling with this simple print and I’ve tried just about everything. (Photo in the comments)

- Printing with standard Anycubic Translucent Green with 8sec exposure on 0.05mm layers with 6 bottom layers exposing 60sec each
- Verified that I am able to print other (much more complex) files just fine
- verified that others have had no trouble with this print ( https://www.thingiverse.com/thing:3453131 )
- the print appears to go alright until the last several layers
- It is at least consistent and I get the same result every time
- Tried with and without supports
- Powered the machine off and on
- Re-leveled
- Verified slice file validity and even watched the printer print the last several layers.

Any advice is greatly appreciated as I thought this would be a quick no-stress print. I guess that’s what I get haha.

翻譯年糕

For everybody that is using a heater in your Photon - you might want to put some weatherstrips (sorry translated by google, not sure it is the right name) on the door closing surfaces (side and top). See the white strips on the pictures. This brought my heater 66% quicker to the set temperature that (20*C room temp to 33*C set enclosure temp in 3.5 min. Instead over >10 min). I am using an 100W 12V heater - modelled my own heating system on the enclosure (still need to put the files on thingiverse - want to adapt it before posting with some thermal runaway stuff due to some post i saw here).

翻譯年糕

Newest print, hollowed, cured
siraya tech fast grey resin
Let prusaslicer do auto supports since chitubox kept crashing when I was doing manual supports
Stl: https://www.thingiverse.com/thing:2834901
Got a little resin on my lip, then licked my lip, so might die now

翻譯年糕

Biggest print I've done so far :)
Frost worm by Schlossbauer
https://www.thingiverse.com/thing:4067846 翻譯年糕

I just had to..... <3

Link to the file

https://www.thingiverse.com/thing:3692023

翻譯年糕

Had my proton for about two months now and I'm continually Blown Away by what it's capable of. Yeah.. Resin printers have some limitations but the things that you can do are pretty amazing. Printed his tractor for my father, try not to criticize my painting skills too much lol. Then I found this rose on thingiverse I just had to try. I didn't have enough red resin left to do a whole lot of anything so I took some clear and mixed what little red I had left. Ended up with this nice pink color. I was super skeptical on that Rose. I figured with the petals being so thin it would just all end up stuck to the bottom of it but it actually printed really nice.

翻譯年糕

My take of the DeStinkyNator for the Photon S, print these: https://www.thingiverse.com/thing:4082951 https://www.thingiverse.com/thing:4097256 and on top of them you will need: 8cm fan raw activated carbon some rubber bands a short length window foam seal or equivalent some plugs and/or eletrical skills I spraypainted the destinkynator itself, then used just the activated carbon in the homemade filter grid (adding a layer or worse two of filter foam was blocking too much the air flow). Results are encouraging: I printed the 2 hours test cube in my other recent post, and I could only smell some weak whiff and nothing else. It's damn noisy though when under the printer, during dry run tests I could only hear a slight fan noise. 翻譯年糕

This is the Fep replacement aid that used to be on Thingiverse. If it needs to be taken down for any reason....go for it.

翻譯年糕

Finally finished my curing container. Only took 24 hours to print. I went ahead and uploaded to thingiverse if anyone is interested. https://www.thingiverse.com/thing:4098131

翻譯年糕

Just set up an air filtration system and ran a ring test print from a free file on Thingiverse

Think it came out right

Sorry for the bad lightning, now to cure it

翻譯年糕