Anycubic Photon Printer Owners 造訪社團 » mac

原文網址 Stuart Glennie
2019-10-12 22:36:41

Hello. I've just fitted a new LCD to my photon. At first the test rectangle seemed fine, but the first test print came out badly. I've been back in the machine and reseated the LCD connection, and these are the results. The patterns that should be there are there, but there seems to be some other stuff too. Does the great Photon give mind have anything to offer?

翻譯年糕

Nick Baskwill
2019-10-12 22:41:28

Danny Lloyd
2019-10-13 02:13:07

原文網址 Marty Khull
2019-10-12 17:27:09

Hi Guys , got my first 2 prints of the Photon today , I'm calling them a success since they came out the machine in 1 piece , but there is a couple of areas I could use some advice on please . 1st 3 pics , the back edge (red circle) appear's to have sagged as well as what appears to be sagging on top sorta flat surface , Im guessing not enough supports ?? . Other thing that caught my eye is the random height lines parrellel to the print plate , I did pause the print a bunch of times to have a look see at how it was going , any possible connection ?? Last pic , this printed well except for the very bottom on the print bed , the bucket was set at 3mm above the plate in the slicer but it looks as if that was to close and the lot just sort of stuck together and turned into a solid mass , bit more angle on the bottom of the bucket and get it higher off the print bed ???. Monocure Clear resin 0.04 layer @10sec , 6 Bot layers @100sec 6.5sec off time .

翻譯年糕

Jon Lamkin
2019-10-12 17:39:16

Arjen Aka Vargen
2019-10-12 17:46:29

Marty Khull
2019-10-13 16:34:27

Arjen Aka Vargen
2019-10-13 17:13:40

Marty Khull
2019-10-13 17:23:26

原文網址 Dave Booche
2019-10-12 08:07:08

Does anyone else Uk based use meth spirits in a non heated ultra sonic machine ??? Does anyone else Uk based use meth spirits in a non heated ultra sonic machine ??? 翻譯年糕

John Harrison
2019-10-12 08:17:00

Dave Booche
2019-10-12 08:18:33

Dave Booche
2019-10-12 08:19:47

John Harrison
2019-10-12 08:22:23

John Harrison
2019-10-12 08:23:20

Dave Booche
2019-10-12 08:25:13

Dave Booche
2019-10-12 08:27:19

John Harrison
2019-10-12 08:27:45

Dave Booche
2019-10-12 08:28:03

Dave Booche
2019-10-12 08:30:00

John Harrison
2019-10-12 08:30:12

Dave Booche
2019-10-12 08:30:42

John Harrison
2019-10-12 08:33:11

Justin Lincoln
2019-10-12 08:35:34

Dave Booche
2019-10-12 08:39:34

Jeff Greenfield
2019-10-12 08:49:02

Ron Luttrull
2019-10-12 09:30:03

Audrey Col
2019-10-12 16:26:13

Alex Vee
2019-10-12 17:24:20

原文網址 Moritz Moe
2019-10-12 04:23:52

Hi there Community,

I am new here and own a „Photon“ since today ?
I hope I will geht some information and tips for beginners here and of course some nice models to print.

I will test the machine tommorow, especially for Tabletop, Dioramas and Busts.

Greetings Moritz Moe

翻譯年糕

Chad Elstad
2019-10-12 05:04:13

Moritz Moe
2019-10-12 05:05:43

Melecio Guzman
2019-10-12 05:12:32

Jared Davis
2019-10-12 05:23:44

Moritz Moe
2019-10-14 01:00:42

原文網址 Riley Esmond
2019-10-11 15:52:45

So I’m out of resin. I’ve only used anycubic green( the one that originally came with my machine and a bottle I ordered). I’m looking for something less brittle. I’ve seen some things about mixing resins on here and wondering what you guys would get. I mostly print miniatures. Any help would be great! Thank you!

所以我沒有樹脂了. 我只使用過任何立方體綠色(最初帶著我的機器和我訂購的瓶子). 我在尋找不那麼薄的東西. 我見過一些關於混合樹脂的事情, 想知道你們會得到甚麼. 我主要列印迷你. 任何幫助都會很棒! 謝謝!

· 查看原文 · 為此翻譯評分

Cam Erasmus
2019-10-11 16:11:11

Ben Gill
2019-10-11 16:16:26

Joe Broggio
2019-10-11 16:22:52

Ash Fielding
2019-10-11 18:23:20

Paul Tyer
2019-10-11 20:09:00

Rick Hanson
2019-10-11 20:31:53

Rick Hanson
2019-10-11 20:32:10

Rick Hanson
2019-10-11 20:32:26

Rick Hanson
2019-10-11 20:35:26

Jay Dubbs
2019-10-11 21:16:09

Benny Lu
2019-10-12 00:20:42

Joe Broggio
2019-10-12 03:03:06

Greg Bauer
2019-10-12 04:00:54

Rick Hanson
2019-10-12 04:13:10

Rick Hanson
2019-10-12 04:14:16

Jake Maverick
2019-10-12 04:54:12

David Anthony Vivas
2019-10-12 11:00:22

原文網址 A.J. Dinsdale
2019-10-11 06:28:44

Sorry for the noob question. I did have a search but hoping for a quick rough answer to this one.

What is the lowest and highest height people have pushed the machine to?
And what are the general rules for settings when going up and down in layer height? Is there a simple equation, as in double times for double heights, or is it more nuanced trial and error?

Thanks again dudes!

翻譯年糕

Smith Hayward
2019-10-11 06:38:32

原文網址 Alex Dixon
2019-10-10 22:43:24

Hey all,

We've had our Photon for about a year now and had many successful prints. Just a couple of hours ago we tried printing and we're getting an awful grumbling noise from the z-axis stepper motor, and it doesn't turn the screw.

The screw turns easily in the hand so it's not seized. We opened up the machine and there are no visible issues (loose wiring etc). Dead stepper motor, perhaps?

翻譯年糕

Jeff Greenfield
2019-10-10 23:36:55

Alex Dixon
2019-10-15 05:54:25

原文網址 Stuart Glennie
2019-10-10 05:01:34

Hello. I've just replaced the LCD on my Photon (original LCD got ripped off when it got stuck to the bottom of the vat). I checked the test rectangle, and all seemed fine. I leveled the build plate and did a short print to test the machine. The print came out with a lot of extraneous material. Upon rechecking the test rectangle it is now full of artifacts and lines on top of the basic test pattern. Is this a duff LCD?

翻譯年糕

Stefan Giudici
2019-10-10 05:18:19

原文網址 Alan Thomson
2019-10-10 01:45:57

Hello new photon owner here.
I’ve done a ton of researching and looked over almost the entire photonsters website and several Chitubox YouTube videos and altered the supports settings accordingly in anticipation of the machine arriving but the one thing I can’t find are the settings options for exposure time etc. Can anyone help me out ?
I’ve added the normal photon option in chitubox but I’m not sure if that’s right.

Oh I’ve also got all the relevant protection and curing stuff either now or incoming too as well as a curing box so it’s basically the settings I’m missing to start up

翻譯年糕

Julio Mata
2019-10-10 01:49:44

Jez Clark
2019-10-10 01:50:27

Melecio Guzman
2019-10-10 01:58:44

Alan Thomson
2019-10-10 03:18:59

原文網址 Michael S Dooley
2019-10-09 13:08:03

So I don't get. Quite a few people here, anycubic is garbage,throw it away and buy an epax or chuck it and buy a whatever better machine. If the Anycubics suck so bad and you've tossed yours, then why the hell are you still here?. Im seriously happy for you that you are independantly wealthy or have a good enough paycheck to buy pro level machines. Some people dont, and some people dont need one and just need a little i.provement to an entry level machine and like tinkering. But if all you are going to do is trashtalk and say chuck it and get something then just shut your hole and get lost. People are asking about the PHOTON not your personal pet machine.

翻譯年糕

Dan Andersson
2019-10-09 13:13:10

Lane Shutt
2019-10-09 13:17:47

George Graves
2019-10-09 13:19:04

Lee Baxter
2019-10-09 13:23:55

Alejandro Salinas
2019-10-09 13:26:29

Adam Foster
2019-10-09 13:27:28

Hector Felix
2019-10-09 13:37:00

Tiernan Messmer
2019-10-09 13:51:34

Tiernan Messmer
2019-10-09 13:53:37

Neil Duffey
2019-10-09 14:00:28

Will Layfield
2019-10-09 14:03:57

Shane Johnson
2019-10-09 14:07:55

Reed Culver
2019-10-09 14:39:18

Benjamin Tolputt
2019-10-09 14:40:09

Franz Meriles
2019-10-09 14:45:03

Benjamin Tolputt
2019-10-09 14:45:35

Benjamin Tolputt
2019-10-09 14:47:14

Benjamin Tolputt
2019-10-09 14:48:34

George Graves
2019-10-09 14:49:51

Benjamin Tolputt
2019-10-09 14:49:56

Will Layfield
2019-10-09 14:52:29

Callum Rex Reid
2019-10-09 15:21:36

Rob Jansen
2019-10-09 15:25:50

Jari Ivanoff
2019-10-09 15:33:29

Leon Photon
2019-10-09 15:36:50

Sen Kun
2019-10-09 15:37:01

Sen Kun
2019-10-09 15:37:37

Sen Kun
2019-10-09 15:51:12

Tiernan Messmer
2019-10-09 16:00:57

Jim Stephens
2019-10-09 17:04:58

George Graves
2019-10-09 17:07:14

Dick Teh
2019-10-09 17:37:51

Minghua Kao
2019-10-09 17:52:44

Minghua Kao
2019-10-09 17:55:16

Benjamin Tolputt
2019-10-09 18:03:25

Benjamin Tolputt
2019-10-09 18:05:30

George Graves
2019-10-09 18:07:13

Benjamin Tolputt
2019-10-09 18:08:08

George Graves
2019-10-09 18:10:10

Benjamin Tolputt
2019-10-09 18:11:17

Julia von Pfaler
2019-10-09 18:19:30

George Graves
2019-10-09 18:41:55

Jon Lamkin
2019-10-09 19:31:52

Benjamin Tolputt
2019-10-09 19:35:23

Jon Lamkin
2019-10-09 19:47:17

Jeremy Swigart
2019-10-09 20:04:13

Jason Turner
2019-10-09 20:25:05

Lee Furry
2019-10-09 21:02:09

Jarrod Smith
2019-10-09 22:06:12

Evan Boone
2019-10-09 23:15:26

Tom Allen
2019-10-09 23:29:31

Melecio Guzman
2019-10-09 23:54:15

Melecio Guzman
2019-10-10 00:01:31

Michael Harley
2019-10-10 01:03:40

Henric Hallgren
2019-10-10 01:23:33

Kelly Filgo
2019-10-10 01:28:31

David O'Maolagain
2019-10-10 01:49:15

Will Layfield
2019-10-10 02:20:43

Nicholas S. Antolick
2019-10-10 02:37:44

Benjamin Tolputt
2019-10-10 05:57:35

Benjamin Tolputt
2019-10-10 05:59:26

Benjamin Tolputt
2019-10-10 06:01:54

Tom Allen
2019-10-10 06:02:53

Tom Allen
2019-10-10 06:03:19

Mika Vienonen
2019-10-10 06:04:56

Melecio Guzman
2019-10-10 06:13:51

Benjamin Tolputt
2019-10-10 06:32:15

Dan Cannon
2019-10-10 07:17:16

Franz Meriles
2019-10-10 10:46:16

Melecio Guzman
2019-10-10 13:05:05

Sergio Romero
2019-10-10 21:53:19

Benjamin Tolputt
2019-10-11 06:09:55

Benjamin Tolputt
2019-10-11 06:13:42

Benjamin Tolputt
2019-10-11 06:17:44

全不選發文排行