Anycubic Photon Printer Owners 造訪社團 » EX

Hi , I am a new owner of an anycubic photon. I have used it twice and the prints came out fine. I have a question about the settings in the Chitubox slicer. I have watched videos of people setting up the settings on the left side of the print profile but not on the right side. Is there a video or a setting sheet to explain these settings? The time of the prints are 3hours 3 minutes for the rook and 4 hours 40 minutes for the yoda. Is there a setting to speed up the time without risking a failed print? TIA

翻譯年糕

Hello guys , I have a small problem .
I am trying to help my friend calibrate his brand new photon.

I am printing calibrating cube, the height is good
But the width isalways around 0.1-0.15 mm wider.

Any idea how to calibrate this?
using Anycubic green resin that came with it.
0.05 height, 5 layers, 60 bottom exposure, 10s layer exposure

Thanks in advance

翻譯年糕

Hello, I wondered if somebody could give me a little advise. I have been 3d printing for just over a year now. Got my Ender 3 in December 2018 (lots of mini and terrain). I wanted to print more detail on my minis so I also bought the Anycubic Photon in December 2019. My cube test print failed slightly, the Z axis screw was quite bent... not good. So I emailed customer support and they sent me a replacement. I changed the part and my next test cube came out fine. I have now printed about 30 minis but have noticed that they have layer lines and it seems to be getting worse. I have moved the Photon away from my Ender 3 just in case the vibrations where unsettling the resin and there has been no change. I have also noticed slight movement of the Z Axis screw (I think). I have re-leveled the bed a few times as one time the print bed had shifted so much that the front had risen by about 2mm. Hence the re-leveling of the bed. Sorry for the essay but I wanted to provide a fully view of my experience so far. Any help would be greatly appreciated.

翻譯年糕

Is there anything that would cause prints to come out less cured over time? I've been running Anycubic plant based grey, and had great results at 10 seconds per layer previously. Last night I pulled some prints off the plate that felt more gummy than usual, and required extra time in the UV curing can, I'm wondering if maybe my FEP is getting cloudy and affecting cure times or something.

翻譯年糕

Hi, I have a problem with vertical streaks running through a model but only in a small area. This is a new problem and is in the machine not the print file.

I have two Photons so I was able to narrow down the problem. I thought it may be scratches on the vat base but exchanging the vat with the good machine did not fix the problem.

I removed the platform and vat and run a dummy print to look at the UV image. I noticed that in the area associated with streaks there are dim pinpricks of light that should not be there. So I deduce the problem is either the LCD display or the electronic drive to it.

Has anybody else had this problem?

Cheers, Bruce

翻譯年糕

Brand new printer, right out of the box. Tried to turn it on a couple of times but the screen does not seem functional. Does anyone have a similar experience or even better a way to fix the problem ? Or should I just send it back and ask for a replacement?

翻譯年糕

So printer arrived far earlier than expected, still need to clear out the garage to make room for it. I've set it up underneath a verenda with the box over the top to block UV light and a blanket over it all to try and keep the inner heat level in the recomended range.

Is there anything wrong with this / is this a fire hazard?

Additionally anyone got exposure settings for anycubic red dialed in?

翻譯年糕

I printed my first multi-piece hollowed mini. The pieces don't fit together.

I used MeshMixer.

Am I STILL getting over exposure due to light bleed? My exposure time is already only 4 seconds.

Photon S
0.02
Elegoo Grey

Thoughts?

Thanks!

翻譯年糕

Currently awaiting my bottle of tenacious, how will it affect the exposure setting when mixed with my normal resin Currently awaiting my bottle of tenacious, how will it affect the exposure setting when mixed with my normal resin 翻譯年糕

Has anyone used yellow transparent resin in a photon s? I cannot, for the life of me, figure out the correct exposure settings, and it's not on the photon s spreadsheet.

翻譯年糕