Anycubic Photon Printer Owners 造訪社團 » EX

I don’t think I’m getting the best quality that my printer is capable of. I find some of the prints missing the detail, potentially look a bit blurry (and melted if that makes sense?).

I think I have my exposure time set at 8s. Is there any harm in pushing this? Using regular Photon with Anycubic white. Base exposure is 60s and I’m quite okay with that.

Washing in IPA, then elbow grease then water!

TIA!

翻譯年糕

Hi, one of my printers has started acting up again.

I have 2 Photon printers. Both are around the same age but the one that gives me issues from time to time is a month older. I set it up this year in January. I started having issues with it a week or so ago where every time that I printed something I’d have to clean the resin vat. There was always some sort of artifact in there stuck to the FEP film. So in between prints I’d drain the vat, scrape off anything that needed to be scraped off, cleaned with IPA and started a new print.

I decided yesterday I’d check the FEP tension as there were some screws on the bottom that looked loose. I found the tension was at about 190hz to I tightened to around 300hz and printed again last night.

Needless to say my print was not good. ?

Seems like I had these issues before and I swapped out the FEP film and everything went back to normal. I can try that again but wanted to see if anyone had any other ideas.

As you can see in the pics there is a lot of extra resin everywhere (especially near the bottom) but I am still getting some nice crisp details. That picture with the space ships the middle model is pretty much destroyed.

Both my printers print the same files. They are on the same firmware and right next to each other.

I do plan on swapping out the film tonight but wanted to see if anyone else had any ideas. Is it normal that the FEP becomes looser after use?

翻譯年糕

Anycubic Photon. What could be going wrong?

Last week I installed a new LCD screen (Anycubic replacement). First prints went well, no fails. The last couple of days I had more and more failed prints: no print in the middle, no print on the left side of the bed etc.

I tried the usuals: cleaning, levelling… Today I wanted to test the printer again: test print of some head in different locations. And the results are more terrible than before.

With my old LCD screen I didn't have this problem, same resin, same settings: 0.04mm, 6s exposure, 7 bottom layer, 80s exposure.

Extra clue might be the apparent loss of detail before and after the new screen.

翻譯年糕

Finished printing this guy off, i just need to prime him and then i can send him to terrify his next group of D&D victims!

翻譯年糕

Hey guys,

I ran a print today with the Anycubic Gray resin, and it came out with awful details.

The Barbarian was yesterday, printed with the Anycubic Green

The other model was printed today with the Gray.

I'm thinking that it's likely an exposure issue, but I cant figure out if it's over or under exposed. Any pointers would be appreciated!

翻譯年糕

All done with the print and the first coats. Next to add the bio hazard logos to it. Perfect for a resin cure box ? ? ? zombie apocalypse cure box!

翻譯年糕

Any experiences printing mini’s with the new Photon Zero yet? Any experiences printing mini’s with the new Photon Zero yet? 翻譯年糕

Hi everyone, my partner and I just ordered a Photon today. I'm reading the FAQ page in the group details and watching the 101 video on youtube from 3D print farm. I'm pretty excited to expand my 3D printing experience from my ender 3 to this. I will do my best to not post dumb questions that I can answer by searching the group/google first :)

翻譯年糕

For Anycubic Photon S owners: I'm wondering what kind of filtering setup you have? I'm looking for recommendations, especially (but not limited to) setups that don't use exhaust hoses as having my printer close to a window is kinda tricky (also, winter ? ).

翻譯年糕

Daphne took a bit of work so far. First I didn't like the idea of seperate body parts as it tends to take away from the details with joint lines. So I scaled it to 80% and put the body back together except the head that can be removed for painting. Then I hollowed it out to save on resin. The results are fantastic. Right now it is just held together with blu-tack for pics and is ready for priming.
Link will be put in comments...

Daphne到目前為止做了一些工作. 首先, 我不喜歡分離身體部位的想法, 因為它傾向於用聯合線條脫掉細節. 所以我把它放大到80然後把身體重新放在一起, 除了可以去除畫畫的頭. 然後我把它挖出來節省樹脂. 結果太棒了. 現在它只是和blu-tack一起拍攝圖片, 準備開始.
連結將在評論中...

· 查看原文 · 為此翻譯評分