Anycubic Photon Printer Owners 造訪社團 » Google

Chitubox light off delay and bottom light off delay both are set by default to 0...I checked the google doc but it's showing very different numbers, is there something I'm missing?

翻譯年糕

There are several additional fields that appear in chitubox that are not present in the anycubic slicer. For the google docs spreadsheet since those extra fields are not listed should i use the defaults?

翻譯年糕

Hi. What exposure time do you use for Anycubic white 0.05 and 0.02mm?
Yes I know about the google doc but it says 15sec? That is for sure too long

翻譯年糕

Any ideas why this happened ?

Printed with Anycubic Red at recommended settings (Google doc sheet), plate leveled, fep tight like a drum...

翻譯年糕

For anyone who's looking for D&D minis to print, here is a huge collection. It's got basically everything from the Monster Manual, plus a lot more.

Original Reddit post: https://www.reddit.com/r/3dprintingdms/comments/cvtz5q/looking_for_stl_files_for_a_particular_monster_or/

https://docs.google.com/spreadsheets/d/1PemvBH7LC-hm4KoeA8OXVu5_k963Vpmw7kOEA_1tzWs/edit 翻譯年糕

Hi everyone, has anyone else had the issue that if using Chitubox to slice the Photon S will just not print anything and then the 2k screen exposure will stop working properly? It looks like this and the only thing that got the test back to normal was re-installing the latest firmware. However, the Photon does not even seem to heat up at all, no odor I expect from the resin in use, and I do not hear the bottom layers creating any suction. After a 40-50 layers I have stopped a few prints to find there is nothing on the build plate or the FEP. They just are not printing at all. I have mostly been using the Elgoo ABS-Like Grey and the settings are verbatim from the Google Doc. Since having to re-install the firmware nothing will print. The ribbon cable for the 2k is intact. Room temp is in the 20s C (68-70 F).

The Photon Workshop just crashes when I try to slice something. And sometimes when just dropping an STL in it. I did not have that problem before I started to use Chitubox, is there a driver conflict or something? Two weeks in and this purchase was pretty much instant regret. Any recommendations for firmware you all are using successfully? I've tried the default 2 dot something, 4.18 and 5.0.2. After about two dozen attempted prints there's only been three I would call acceptable and those were early and poorly supported as I have been learning. The FEPs have been tuned to ~350hz w/ Spectrum from the apple app store. I have to wait for more of those to come in now. Gone through six FEPs now I think between one that got melted in the corner, the one it came with was creased and then not finding a way to actually tune the things until a day or two ago. Interestingly, the only decent prints i got were before I had a way to measure the frequency. I don't like just returning things but I doubt there is problem forum I have not read on the Photon S at this point. I have had a few ok prints so I am not looking to blame this on any of the STLs themselves, this feels like an issue with the device. and yes, before it said the build plate is level and zero'd.

Any ideas? Please and thank you.

Example of what happens after I use Chitubox(not me in the vid):
https://youtu.be/KA75JRI3vDw

翻譯年糕

Latest Fail

0 of 6 so far

Tried multiple settings, multiple structures, multiple levels, everything is clean, different models. starting to get very frustrated. and from the lack of success that seems to be happening on this page.... I am not the only one feeling the pain.

Here is my latest fail settings straight from the google doc. line 27? i think. Doesn't work. should be updated and no bueno.

Closest thing I have had to a success was what I posted a few days ago, but that was hardly a success as I could not trim the supports as the print was way too brittle and snapped pieces off my model.

any help, advice, or anything to stop me from hucking this pos across the room

Along with your advice, should you be so kind as to provide some, please post RECENT successes to give me some inspiration to keep going.

TIA

翻譯年糕

Thanks for the add... just ordered my printer and bottle of their new plant based uv resin... been watching lots of videos so pulled the trigger on this.. So from what I've watched so far I'll need to buy or build a simple uv curing setup? So without posting links, I found a "Curing Light Solar Powered Rotary Display Stand Turntable Kit for SLA DLP 3D Printer " for $33 . I assume this would fit the bill, or simply set outside, but I wouldn't want them to get dirty etc.. So what else besides rubbing alcohol will I be needing to purchase? What consumables? (besides gloves etc) . I found a good shared google doc listing many resin types and multiple settings people suggest, im sure that will be useful, I'm confused with all the resins though any why some wont work etc.. and what happens if the setting simply is not right? Does the unit have built in settings for various resins perhaps? I'd like a tough resign to make things like keychains, and things that might be outdoors in the elements.. can anyone suggest some and why? I saw formlabs I believe it was tough resin but it was like $145 If my memory serves me... isn't there others that are durable... Don't want just a toy with things that break easy... After curing etc, how many of you paint your items, any specifics on types of paints to use?

翻譯年糕

Hey there!

I'm using my Photon and ChituBox since month and never had any big issues (minor only), but this is new:

I'm loading STLs into Chitubox, as usual, arrange them, add supports and go to slice them... but now, when I want to save or browse through the slices, Chitubox just closes/crashes...

Happens with old and new version...

Any ideas? Tips tricks? My google skills didn't find anything.

Thing is, I also already printed these files a few days ago. I just scaled them a little bit up and put on new supports in 7mm height instead of 5mm... Lowering the model to 5 mm again also ends in the same issue!

Hope anybody can help :)

翻譯年糕

Hey guys, so I tried my first non-test print. The test print case out fine, then I releveled the bed after feeling more confident with it and printed the baby yoda (made in this group). I sliced it with the photon slicer according to the google doc for anycubic white resin (15s exposure). This is what came out. Any ideas?

翻譯年糕