Anycubic Photon Printer Owners 造訪社團 » github

原文網址 Alessandro Vasapolli
2019-03-11 03:32:42

Have you ever tried printing at 0.01?
I need to make some extremely detailed molds and I need the best possible z-axis resolution...
If so, how much do you increase the exposure from 0.025? I've tried to look but there is no exposure test print available on the github tests prints.
Thank you!

翻譯年糕

Marcin Kudzia
2019-03-11 03:33:40

Richard Pigott
2019-03-11 04:24:07

Ettore Maria Bar
2019-03-11 04:39:54

Sen Kun
2019-03-11 04:48:18

Alessandro Vasapolli
2019-03-11 05:18:42

Alessandro Vasapolli
2019-03-11 05:18:58

Robert Silvers
2019-03-11 10:03:23

Robert Silvers
2019-03-11 10:04:18

Alessandro Vasapolli
2019-03-11 16:50:21

Robert Silvers
2019-03-11 19:07:48

Dani Martinez
2019-03-11 19:54:31

Alessandro Vasapolli
2019-03-11 20:03:46

Robert Silvers
2019-03-11 22:29:18

原文網址 Stefan Lindström
2019-03-05 15:51:55

Has anyone played around with Slic3r Prusa Edition. In their new Alpha you can slice for their upcoming SL1. Looks really nice, this is a slicer that would be awesome to be able to use with the photon.
Sure you can use it for supports and export the stl but I like the way slic3r have material profiles and stuff like that. There are corrections for size and material shrinkage and lots of fun stuff.
And its open source so maybe someone alot smarter then me can make something with it.

https://github.com/…/Sl…/releases/tag/version_1.42.0-alpha7…

翻譯年糕

Christopher Botha
2019-03-05 16:00:46

Stefan Lindström
2019-03-05 16:11:31

Savio Ku
2019-03-05 16:20:49

Ricardo Frederiks
2019-03-05 18:24:57

Stefan Lindström
2019-03-05 18:26:12

Stefan Lindström
2019-03-05 18:28:28

Ricardo Frederiks
2019-03-05 18:28:28

Ricardo Frederiks
2019-03-05 18:29:29

Stefan Lindström
2019-03-05 18:31:31

Ricardo Frederiks
2019-03-05 18:32:35

Chris Warkocki
2019-03-05 22:08:40

原文網址 Hans De Jong
2019-02-27 01:02:42

Hello, I created a small command line utility that converts the horizontal dimensions inside a .photon file to more closely fit design dimensions. Normally all objects are about 100um wider, and holes are about 100um narrower. This is likely because of light bleed through from edge pixels. My utility works by trimming one pixel from all edges in each image that is in a .photon file.

I uploaded the source code to github:
https://github.com/Hans2004/AnyCubic-Photon-Decrease-Pixel

The program is written in C++ and uses no external libraries. Therefore it is easy to compile.

Does anyone know how I can add a reference to the photonsters github site?

翻譯年糕

Milton Maxson
2019-02-27 01:22:26

Darren Tarbard
2019-02-27 02:08:36

Milton Maxson
2019-02-27 02:23:17

Hans De Jong
2019-02-27 02:45:50

Hans De Jong
2019-02-27 02:47:28

Hans De Jong
2019-02-27 02:49:07

陳彦廷
2019-02-27 11:39:43

Robert Silvers
2019-02-27 13:17:56

Robert Silvers
2019-02-27 13:22:45

Hans De Jong
2019-02-27 19:41:58

Hans De Jong
2019-02-28 20:14:21

Robert Silvers
2019-02-28 22:01:19

Hans De Jong
2019-03-01 00:33:05

原文網址 Chris D'Andrea
2019-02-26 01:32:51

OK so lets talk Settings. I am using the Anycubic Green Resin. I purchased a 1 liter bottle with my printer. I had good results but sporadically it would fail and I would have a base with SOME supports left and a blob on the FEP. So I figured I would test the resin using the file on Github. Looking at this image it says I need a 16 - 20 sec exposure time right? The best looking result is between 8 & 10 column. That is FAR from the 5.5 (or anything at all) on the recommended settings spreadsheet on google docs. Can anyone help me understand what I should be printing at here? This is the 50u B100 2-20 file. I got similar results on the 25u. Maybe I'm just not interpreting things right.

翻譯年糕

Christian Plösser
2019-02-26 01:37:46

Sen Kun
2019-02-26 03:05:07

Philippe Maegerman
2019-02-26 22:36:52

Sen Kun
2019-02-26 22:40:29

Nick Williams
2019-02-26 22:43:46

Nick Williams
2019-02-26 22:44:01

Chris D'Andrea
2019-02-27 00:02:54

Nick Williams
2019-02-27 00:36:31

Chris D'Andrea
2019-02-27 03:44:31

Chris D'Andrea
2019-02-27 03:44:47

Chris D'Andrea
2019-02-27 03:44:52

Chris D'Andrea
2019-02-27 03:45:02

Chris D'Andrea
2019-02-27 03:45:20

Christian Plösser
2019-02-27 07:54:25

Chris D'Andrea
2019-02-27 07:55:40

Chris D'Andrea
2019-02-27 07:56:40

原文網址 Casey Shiray
2019-02-25 20:38:05

I may have leveled my printer incorrectly, or I’m reading the Github page wrong.

“Remember that as you tighten the setting (grub) screw it will move the plate down a tiny fraction more. You will find that you cannot pull the paper anymore, so you should raise / backoff the build plate level by 0.1mm increments until the plate is gripping the paper with even resistance, and that you can pull but not push it back. Then only set Z=0.”

So after doing the paper test AND tightening the setting screw, I should have backed off the plate until I could move the paper again—then set Z=0?

翻譯年糕

Bradley VanScoyk
2019-02-25 20:39:23

Christopher Elliott
2019-02-25 20:46:01

John Rudisill
2019-02-25 22:12:40

Sen Kun
2019-02-25 22:22:49

Casey Shiray
2019-02-25 23:31:14

原文網址 Sen Kun
2019-02-25 03:02:51

Dear new Photon owners, please read this.
PSA

All Photons ship with the FEP film preinstalled in the vat. They used to be tensioned correctly from the factory. However, this may no longer be true as the Amazon listings now include the warning pictured.

The instruction booklet does not warn you to check FEP tension. If you did not notice this warning, and did not tighten the FEP, you may get print failures due to an under-tensioned FEP.

However, if you did receive a vat with already correctly tensioned FEP from factory, and you still followed the warning instructions and further tightened it, you may get print failures due to an over-tensioned FEP.

The only way to be sure is to check!

https://github.com/…/anycubic-photon-do…/blob/master/FAQ.md…

親愛的新的光子主人, 請閱讀這個.
Psa

所有光子船都裝在增值稅中安裝了fep薄膜. 他們以前是從工廠正確的. 然而, 這可能不再是真的, 因為亞馬遜上市現在包含了所描繪的警告.

指示手冊沒有警告你檢查fep緊張局勢. 如果你沒有注意到這個警告, 而且沒有收緊fep, 你可能會因為太低的fep而列印失敗.

但是, 如果你確實收到了工廠已正確租用fep的增值稅, 而且你仍然遵循警告指示並進一步收緊, 可能會因為過高的fep而列印失敗.

唯一確定的方法就是檢查!

https://github.com/Photonsters/anycubic-photon-docs/blob/master/FAQ.md#how-tight-exactly-should-the-fep-be-tensioned

· 查看原文 · 為此翻譯評分

Thomas Salavert
2019-02-25 03:05:16

Sen Kun
2019-02-25 03:07:37

Benjamin Matthews
2019-02-25 03:19:51

Sen Kun
2019-02-25 03:22:26

Dime Les
2019-02-25 03:48:03

Kevin Sharp
2019-02-25 04:37:54

Sen Kun
2019-02-25 04:46:26

Travis Hunt
2019-02-25 05:00:22

Dani Rose
2019-02-25 05:02:07

Travis Hunt
2019-02-25 05:03:33

Sen Kun
2019-02-25 05:16:56

Sean Poeschl
2019-02-25 05:45:52

Pijvs Magnifiqvs
2019-02-25 06:16:09

Chris Kelly
2019-02-25 06:48:26

Andrew Delisle
2019-02-25 09:37:33

Jawad Abuasabeh
2019-02-25 10:19:22

Travis Hunt
2019-02-25 11:27:11

Andrew Delisle
2019-02-25 13:14:34

Chris D'Andrea
2019-02-26 04:36:14

Travis Hunt
2019-02-26 05:02:43

Richard White
2019-02-26 17:17:34

Sen Kun
2019-02-26 17:32:33

Richard White
2019-02-26 17:33:38

Travis Hunt
2019-02-26 22:31:26

原文網址 Andrew Bills
2019-02-23 14:51:49

First post but I did go through the GitHub first.... It could be the weather here playing a factor but the side profile of this print shows my initial layers were a bit droopy (best angle to demonstrate) where the final layers were nice and level/flat. Is this I removed too many supports thing or a settings thing or...? I used the known good exposure settings for the anycubic white.

翻譯年糕

原文網址 Florian Sepp
2019-02-21 16:00:22

my Photon reboots after the first layer. I heard, that this is a common bug. I already tested the power adapter which seems to be fine. Next I wanted to update the firmware but besides the firmware 1.1 on the anycubic website there are firmwares on github. which should I use?

翻譯年糕

Alex Vee
2019-02-21 16:12:12

Florian Sepp
2019-02-21 16:30:25

Alex Vee
2019-02-21 16:42:14

Florian Sepp
2019-02-21 16:56:58

Sen Kun
2019-02-21 17:10:25

Florian Sepp
2019-02-21 17:16:41

Frank Fickel
2019-02-21 17:35:53

Sen Kun
2019-02-21 17:42:41

Frank Fickel
2019-02-21 17:44:04

Sen Kun
2019-02-21 17:51:50

Brent Steffen
2019-02-23 11:17:43

原文網址 Tachion Tachion
2019-02-21 01:48:08

Dear all, a very important remark on the resin exposure settings on the shared excel file "Anycubic Best Resin Settings" with the low-cost 3D-Okay resin. The values put in for the 3D-Okay resins are REALLY REALLY off !!! By using the resin-xp-finder ( https://github.com/altLab/photon-resin-calibration ), a 0.05mm (50um) Layer can be properly exposed ONLY with at least 20-22 sec !!! This means that 3D-Okay is a pretty BAD resin pushing the printing time to almost 2.5 times the time with Anycubic, Elegoo, FunTo Do, Ameralabs resins.
SO BE VERY VERY CAREFUL WHEN BUYING THIS LOW-COST RESIN!!!

翻譯年糕

Jannick Langfahl
2019-02-21 03:28:09

Tachion Tachion
2019-02-21 21:49:09

Tachion Tachion
2019-02-21 21:49:38

Tachion Tachion
2019-02-21 21:51:36

Jannick Langfahl
2019-02-21 22:47:30

原文網址 Calvin Hobbes
2019-02-18 08:51:15

Has anyone tried mixing 10% Monocure Flex Rapid into the Anycubic transparent green? I'd like to find out what if any changes to the exposure times etc are necessary without wasting a load of resin on tests, if possible. I checked the github first.

翻譯年糕

全不選發文排行