Anycubic Photon Printer Owners 造訪社團 » 螢幕

OK i am old, 48 years as a bench jeweller. trying to prove you CAN teach an old dog new tricks.

Ok I did the sample cube, followed all the instrctions .. CAME OUT FANTASTIC. Made it small to save time..

Today i tried a ring..after 2 HOURS i could finally see under the build plate ( i put a bit too much resin in) and there was nothing there :(

I think that when i levelled the plate using the piece of paper method , i was over cautious?? with a 0.1mm down it was too tight and then 0.1mm up it was too loose.. I left it loose as i didnt want the Z to move down too far and break something.. When i clean out the tray tank the starting raft was attached to the plastic film.. Do you think that is why it didnt work . the build plate didnt lower enough to let the raft attach ??

Ive attached my 3 screen shots just in case i am doing somthing else glaringly obviously wrong..

would appreciate any one help if you dont mind please..

好吧, 我老了, 作為一個長椅珠寶48年. 試圖證明你可以教一條老狗新把戲.

好吧, 我做了樣式立方體, 跟著所有的插圖.. 出來太棒了. 讓它小, 節省時間..

今天我嘗試了一個戒指.. 2個小時後, 我終於可以看到了(我放太多樹脂), 那裡甚麼都沒有 :(

我想我用紙張方法把盤子放在板上時, 我太小心了?? 0.1 mm的0.1 mm, 太緊了, 然後0.1 mm up.. 我離開了 因為我不想z移動太遠了, 打破一些東西.. 當我清理托盤箱時, 起始船被附在塑料膠片上.. 你覺得這就是為什麼它不起作用的原因嗎? "我是一個真正的??

我附上了我的3張螢幕截圖, 以防萬一我做其他事情顯然是錯的..

如果你不介意的話, 會感謝任何人幫忙..

· 查看原文 · 為此翻譯評分

Just a quick question. I tried to search for the answer but I would appreciate for a more clear answer before I make a wrong purchasing decision :-) Are 2k LCD screens are interchangeable between Photon and Photon S? Should I buy Photon 2K LCD replacement for my Photon S?

只是一個快速的問題. 我試圖尋找答案, 但我希望在我做出錯誤的購買決定之前得到一個更明確的答案 :-) 2 k lcd螢幕可以在光子和光子之間互換嗎? 我應該買光子2 k lcd代替我的光子s嗎?

· 查看原文 · 為此翻譯評分

hello, just got my photon and i want to level it. i am doing it like that:
https://www.youtube.com/watch?v=qEaNVfT8y9w&feature=youtu.be

the problem is: when i try to make the build plate "flat" with the screen. i go down when the paper doesnt move easy , puhsing down the buildplate and then i tighten up the screw, after that i home and then i see, that the Gap which remain at home on the backside of the buildplate is much more than in the front, how can that be possible? tried 2 times, always the same...

你好, 剛拿到我的光子, 我想把它升級. 我這樣做:
https://www.youtube.com/watch?v=qEaNVfT8y9w&feature=youtu.be

問題是: 當我試圖用螢幕使構建板"平 當紙不容易移動的時候, 把建築板拉起來, 然後我收緊螺絲, 然後我回家, 然後我看到, 留在家裡的後面的差距遠遠超過了. 前面, 這怎麼可能? 試過2次, 總是一樣...

· 查看原文 · 為此翻譯評分

Hey Guys, so... i have a few questions i would like for the community to help me with. Sorry it will be a bit of a long post xD.

I got my Photon this week. Here's what i did (questions come after :p ).

- Checked everything was working properly working, turned on the printer, checked if the Z-Axis was moving, if the screen was ok, etc.

- Ditched the stock PSU and USB drive (tested the PSU and its outputing the correct voltage but i ditched it anyway), im using another one i had here with the exact same specs, USB drive im now using a Kingston one.

- Disconnected the "smelling" fan from the main board to avoid the fumes from getting out and stinking up the place. (Planing to upgrade the stock led cooling fan, suggestions???)

- Checked every screw to see if everything was properly tightened (the buildplate wasnt, it would move even after tightening the grub screw).

- Checked the FEP tension with a sound analyzer, it was below 300hz... tuned it to 345-355hz.

- Applied Kapton tape to the borders of the screen (to avoid a spill going into the machine in case that happens).

- Adjusted the buildplate to be completely flat against the screen, made sure that the plate was making even pressure on the paper on all sides (front, back, left and right). After that i leveled the printer and set the new Z=0 (didnt forget to hit Home first :p ).

- Finally i heated up the resin (room temp was 19C) and started the default print file that came with the printer (photos attached).

So, now some questions.

1 - The new yellow windows, how good are they at blocking UV? The printer is not on a direct sunlight enviroment, not even daylight for that matter, but the room does have okayish lighting (there is no light directly above the printer), i am safe to assume resin wont cure while inside? I know i can cover up the printer but im trying to understand if its really necessary.

2 - Do you guys filter the resin and clean the vat after every print? I saw some people mentioning it... but to be completely honest i've never done that with my other printer, well... my other printer doesnt have the leaking risk this one has... So... what do you guys do?

3 - Firmware... my printer came with version 4.2.3... I dont see that in Anycubic site, anyone has the changelog for this fw? Just curious.

4 - Recommendations for resin, im looking for high detail. Impact resistance is not really important right now (Anycubic resins, how do they stack up against the competition?)

5 - Which one is better for the screen to last more? Slow or fast resins?

And for now thats it! Thanks guys...one of the reasons i got the Photon was for this awesome community =)

嘿, 夥計們, 所以... 我有幾個問題想讓社羣幫我解決. 抱歉, 這將是一個漫長的帖子xd.

我這周得到了我的光子. 這就是我所做的(問題之後: p).

-檢查一切正常運作, 開啟印表機, 檢查z軸是否移動, 螢幕是否正常等等.

-丟棄了存貨psu和usb驅動器(測試psu及其輸出正確的電壓, 但我還是拋棄了它), 我在這裡使用了另一個, usb驅動器, usb驅動器現在使用金斯敦.

-從主板上斷開"聞"風扇, 以避免煙霧出來, 讓地方臭. (計劃升級庫存led冷卻風扇, 建議???)

-檢查了每個螺絲, 看一切是否都收緊了(建築板沒有, 甚至在收緊後也會移動).

-用音效分析儀檢查了fep緊張, 低於300 hz... 調到345-355 hz.

-將kapton磁帶應用到螢幕的邊界(以防發生洩漏到機器).

-調整構建板完全平坦, 以確保板塊對紙板對紙面(前, 背面, 左和右)施加壓力. 之後, 我平平了印表機, 設定了新的z =0 (沒有忘記先打家: p).

-最後我加熱樹脂(房間溫度為19 c), 並啓動了印表機的預設列印檔案(照片附後).

所以, 現在有一些問題.

1-新的黃色窗戶, 阻擋紫外線有多好? 印表機不在直接陽光環境上, 連白天也沒有, 但房間確實有okayish照明(印表機上方沒有光), 我可以安全地假設樹脂治癒嗎? 我知道我可以掩飾印表機, 但我試著理解是否真的有必要.

2-你們在每次列印後過濾樹脂並清理增值稅嗎? 我看到有些人提到它... 但老實說, 我從來沒有和我的另一個印表機做過, 好吧... 我的另一個印表機沒有洩漏風險... 那麼... 你們這些傢伙是甚麼? 做甚麼?

3-固件... 我的印表機有4.2.3. 版.. 我沒看到在任何立方體網站, 有人有這個fw的改裝? 只是好奇.

4-樹脂推薦, 我正在尋找詳細的細節. 現在抵御衝擊並不重要(任何立方體樹脂, 他們是如何堆積起來對抗競爭的?) 你知道嗎?

5-哪一個更好讓螢幕持續更多? 慢或快速樹脂?

現在就這樣! 謝謝大家... 我得到光子的原因之一是這個很棒的社羣=)

· 查看原文 · 為此翻譯評分

Well that was a fail. Got my replacement screen today. Shattered the top glass trying to pry it off.
Maybe Anycubic could find a better way of putting the glass on.

嗯, 這是一個失敗. 今天得到了我的更換螢幕. 打碎了頂部玻璃, 試圖打碎它.
也許anycubic可以找到更好的方法把杯子戴上.

· 查看原文 · 為此翻譯評分