Anycubic Photon Printer Owners 造訪社團 » 設定

Ok folks I got my printer got it set up and printed the cube. My opinion the cube turned out good. But now as a newbie where should I start as in trying to learn how to take a file from thingiverse and slice with Chitubox and print because the earrings I tried was a total fail

好了, 朋友們, 我得到了我的印表機設定並列印了立方體. 我認為立方體結果很好. 但現在作為一個新人, 我該從哪裡開始, 學習如何從thingiverse和切圖盒和列印, 因為我嘗試的耳環完全失敗了

· 查看原文 · 為此翻譯評分

Hi team, any obvious reason for my supports failing? It happens for heavy and light supports. I do not have the print settings with me but i have added in some Flex. Perhaps too much? Poor quality resin? It does not seem to be a calibration issue?

嗨, 團隊, 我的支援失敗有任何明顯的原因嗎? 它發生在重力和輕度的支援. 我沒有列印設定, 但我新增了一些flex. 也許太多了? 質量差的樹脂? 這似乎不是校正問題嗎?

· 查看原文 · 為此翻譯評分

A very small print, about 2.8 cm long.
Any thoughts on how to set this up for best results?
(Anycubic Photon)

一張非常小的列印, 大約2.8釐米長.
對於如何設定這個以獲得最佳結果有任何想法?
(任何立方體光子)

· 查看原文 · 為此翻譯評分

https://www.myminifactory.com/object/3d-print-ogre-armoured-mount-32mm-scale-106344
Has anyone printed this? Need help with supports. Mine currently rip away at some point in the print. Not sure how to orient the model and setup supports to make it work.

https://www.myminifactory.com/object/3d-print-ogre-armoured-mount-32mm-scale-106344

有人列印了這個嗎? 需要支援的幫助. 我的目前在印刷的某個時候撕開了. 不確定如何定向模型並設定支援使其運作.

· 查看原文 · 為此翻譯評分

Hi Guys ! I've been studying all you kind fellows are advising on this group in order to get a nice and clean print ! But I keep failing ! I join to this post pictures and settings of my latest attempt.
Just to mention, I followed the latest autosupport parameters from vfx forge which seemed good.
The file has also been checked by photon file validator.
I forgot to save the stl... Sorry for the shitty preview I found
If anyone can help, it would be great ! :D

嗨, 夥計們! 我一直在研究你們所有善良的研究員都在這個小組上建議, 以便獲得一份漂亮而乾淨的印刷! 但我一直失敗了! 我加入這個帖子圖片和我最近嘗試的設定.
順便說一下, 我遵循了vfx forge的最新自動支援參數, 這看起來不錯.
該檔案也經過光子檔案驗證器檢查.
我忘了儲存stl... 抱歉我發現的糟糕的預覽
如果有人能幫忙, 那就太好了! 你知道嗎?

· 查看原文 · 為此翻譯評分

Hi, how would you translate the results of this test into settings(ex. angles)?..The Formtest

嗨, 你會如何將這次測試的結果轉變為設定(例如角度)?.. formtest

· 查看原文 · 為此翻譯評分

Just a quick question! Is this a leveling issue?

I have multiple parts set up on my build plate. The issue I am having is, only one or two will print. the other will not adhere to the buildplate, and just print at the bottom of the vat.
I have had success with these objects at the settings I am using before. The only difference is I mirrored the objects (to print the left arm to match the right arm)

So the image example, the forearm part was the only one to print, the other two did not adhere. whereas they had before I mirrored the object.
Surely this indicated a levelling issue, correct?

I level using the paper method and generally don't have much issue until now. Any tips or leveling techniques are welcome!

只是一個簡單的問題! 這是一個平穩的問題嗎?

我的構建板上有多個部件. 我遇到的問題是, 只有一兩個會列印. 另一個人不會堅持建築板, 只是列印在增值稅底部.
我在以前使用的設定中, 這些物件成功了. 唯一的區別是我反射物件(列印左臂以匹配右臂)

所以影象例子, 前臂部分是唯一列印的, 另外兩個沒有堅持. 而他們在我反射了這個物體之前.
這肯定表明瞭一個平穩的問題, 對嗎?

我用紙張方法平分, 現在一般都沒有甚麼問題. 歡迎任何提示或平平技術!

· 查看原文 · 為此翻譯評分

I'm pretty happy with how this print is coming along, using Anycubic Skin. Had to set my base exposure to 115 sec to get things to adhere to the buildplate but haven't had any issues since then!

Is there any easier way to try and account for shrinkage in resin so I don't have to constantly sand the heck out of my models to fit together, or is sanding just inevitable?

我對這個列印的進展相當滿意, 使用任何cubic面板. 必須把我的基礎曝光設定為115秒, 才能讓事情堅持到建築板, 但從那以後就沒有任何問題!

是否有任何更容易的方法來嘗試和計算樹脂的縮小, 這樣我不用不斷地從模型里沙出來適應, 還是是不可避免的?

· 查看原文 · 為此翻譯評分

A big ‘thank you’ to this group!
I’m fairly new to 3D printing, bought my Photon S last November and I’m having fun printing 40k minis. Been learning through lots of trial and error. Went thru a 1Lt. bottle of AnyCubic Macaroon Blue ECO resin. Unfortunately, my models have all suffered from over exposure because I read some bad information regarding the ECO resin and settings. I was lead to believe that I should be using 12sec exposure times at 0.02mm layers. My mini models were losing details like crazy and I was getting frustrated because I knew it could be better.

This group is helping my understand this machine better and I greatly appreciate the collective knowledge that everyone is willing to share.

I’ve been experimenting more lately with the AmeraLabs SLA tests. I think I’m getting closer to a good balance with the details.

Number one lesson y’all taught me so far:
“The print exposure is too damn high.” Lol
So I made a meme for it lol

給這個社團的"謝謝"!
我相當新到3 d列印, 去年十一月買了我的光子s, 我很開心印刷40 k minis. 經歷了很多考驗和錯誤. 穿過1 lt. 一瓶任何cubic macaroon blue eco樹脂. 遺憾的是, 我的模特都因為我閱讀了一些關於生態樹脂和設定的壞資訊而遭受了影響. 我相信我應該在0.02 mm層使用12秒曝光時間. 我的迷你模特像瘋了一樣失去了細節, 我感到沮喪, 因為我知道它會更好.

這個小組幫助我更好地理解這台機器, 我非常感謝大家願意分享的集體知識.

最近我一直在嘗試ameralabs sla測試. 我想我越來越接近與細節的平衡.

到目前為止, 你們都教我的第一課:
"列印曝光太高了." lol
所以我為此做了一個meme lol

· 查看原文 · 為此翻譯評分

Will re-slicing a .photon(s) file affect quality?

I've got a good .photons file with support etc. where I need it. But I want to print it with different resin, so I need to slice it with the correct settings. Is this possible, or will it affect quality when the starting file is not a .stl ?

將重新切片a. 光子檔案影響質量?

我得到了一個很好的. 有支援的光子檔案等等. 我需要的地方. 但我想用不同的樹脂列印, 所以我需要用正確的設定來切片. 這是可能的, 還是會影響開始檔案不是a的質量. Stl?

· 查看原文 · 為此翻譯評分