Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Trevor Kennemer
2019-07-06 04:01:49

So do I need to replace my FEP film? I have not had a successful print in over a month! Starting to go crazy over what the problem is.

翻譯年糕

Ty Mansfield
2019-07-06 04:04:34

Trevor Kennemer
2019-07-06 04:06:26

Stefan Giudici
2019-07-06 04:18:55

Ty Mansfield
2019-07-06 05:01:44

Hamza Doğan
2019-07-06 06:05:51

Nelson Phoung
2019-07-06 14:10:33

Jannick Langfahl
2019-07-06 16:19:14

Mark Wardle
2019-07-06 21:21:31

原文網址 Trevor Kennemer
2019-06-30 05:52:32

having some issues with chitubox. I want to add infill to my part but no matter what settings I use, it wont generate any infill!

翻譯年糕

Mark Wardle
2019-06-30 11:21:38

Trevor Kennemer
2019-06-30 19:16:07

Maurice Criddle
2019-07-01 02:53:02

原文網址 Trevor Kennemer
2019-01-13 15:43:16

Anybody have any advice on how to keep transparent resin from turning yellow? I'm using transparent elegoo resin.

翻譯年糕

Jure Slokar
2019-01-13 16:35:07

Guti Gutmann
2019-01-14 17:20:13

Richard Shapiro
2019-01-16 11:06:22

原文網址 Trevor Kennemer
2019-01-11 13:30:51

So I have a stupid question. I'm printing an electric violin and it's going to be hollow with 6mm thick walls. When I go to post cure it in my UV chamber, will the UV light be able to permeate all the way through the 6mm walls to fully cure ALL of the resin?

翻譯年糕

Mark Wardle
2019-01-11 14:03:30

Trevor Kennemer
2019-01-11 19:16:01

原文網址 Trevor Kennemer
2019-01-01 09:35:45

Want to get your opinions on removing support material. Do you guys remove before or after curing? I have heard people doing it both ways. What do you guys do? and why?

翻譯年糕

Richard Shapiro
2019-01-01 09:38:47

Erik Cederberg
2019-01-01 09:39:39

Peter Ede
2019-01-02 16:31:06

原文網址 Trevor Kennemer
2018-12-31 22:53:38

Why does this keep happening? Supports keep printing fine but a few layers into the actual print, the part is getting stuck to the fep film!

翻譯年糕

Chris Crute
2018-12-31 22:57:20

Dave Coggan
2018-12-31 23:29:50

Ben Tseng
2019-01-01 00:01:06

Wesley Dowell
2019-01-01 01:09:18

Arizeta Zaft Aeug
2019-01-01 02:13:14

Trevor Kennemer
2019-01-01 02:14:32

Joe File
2019-01-01 04:16:08

Arizeta Zaft Aeug
2019-01-01 04:17:42

Pa Wel
2019-01-02 03:48:38

Trevor Kennemer
2019-01-02 07:09:23

原文網址 Trevor Kennemer
2018-12-30 13:02:39

So just tried starting my second print after successfully printing the photon cube and noticed that there is a big glob of hardened resin at the bottom of my vat. how to I get rid of it?

翻譯年糕

Mark Wardle
2018-12-30 13:04:40

Robert Silvers
2018-12-30 13:20:35