• 3D列印服務
  • #maker+t=market
  • COSPLAY 3D 建模
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Jason Croft
2019-04-09 15:14:43

Hi is there a way to shorten the supports on a shallow build like this ? They are almost 3x the height of what I'm trying to print so add huge build time :)

翻譯年糕

Zena Andreou
2019-04-09 15:23:03

Jason Croft
2019-04-09 15:32:46

Savio Ku
2019-04-09 15:46:52

Zena Andreou
2019-04-09 15:57:34

Jason Croft
2019-04-09 15:58:33

Zena Andreou
2019-04-09 16:02:17

Blake Moody
2019-04-09 16:38:21

Silas Bo Nielsen
2019-04-09 18:22:45

Jason Croft
2019-04-09 18:24:14

Christian Plösser
2019-04-09 18:44:25

Michael McElrath
2019-04-09 21:45:48

Milton Maxson
2019-04-10 02:36:07

Chad Elstad
2019-04-10 04:33:29


原文網址 Jason Croft
2019-04-07 15:51:51

Hi it's me again :)

I have a printer of extremes it seems, yesterday not sticking to plate and today after what I thought was perfect calibration It's all sticking TOO well now !
So previous to this I removed a few of these prints and they came off fine now they are breaking at the points indicated.
Is there something I am missing in the initial Z=0 as in am I over calibrating should I cure for less time ? Whatst he best solution as I am at a loss and not sure I can calibrate it for like the 10th time in 24 hours :)

翻譯年糕

Martin Mjöllnir Umgjer
2019-04-07 16:04:47

Jason Croft
2019-04-07 16:08:41

ßeĥ Ŗȍoȥ
2019-04-07 16:13:09

Jason Croft
2019-04-07 16:15:47

ßeĥ Ŗȍoȥ
2019-04-07 16:19:50

Martin Mjöllnir Umgjer
2019-04-07 16:56:03

Jason Croft
2019-04-07 16:57:08

Jason Croft
2019-04-07 17:08:00

Jure Slokar
2019-04-07 17:29:02

Jure Slokar
2019-04-07 17:29:11

Jason Croft
2019-04-07 17:37:43


原文網址 Jason Croft
2019-04-06 15:52:54

Ok my very last, maybe, question for the day.

Recalibrated lots of advice, thank you all, started a print...

Walked past it it seems to make a "thump" sound each time it lifts never really heard this before should I reset "home" and recalibrate to be less tight on the paper by like 0.1 or whatever it is ?

*As if what's being cured then sticks to the FEP is what I mean*

翻譯年糕

Carla Birch
2019-04-06 15:56:24

Jure Slokar
2019-04-06 15:58:24

Jason Croft
2019-04-06 16:04:25

Gavin Turnbull
2019-04-06 16:14:21

Ingo Strohmenger
2019-04-06 18:45:16

Silas Bo Nielsen
2019-04-06 20:41:23

Chris D'Andrea
2019-04-06 22:37:34


原文網址 Jason Croft
2019-04-06 14:50:35

Ok after n00bing it up with leveling to 0 I found that one side of the plate holds paper better then the other, it's not level.
I loosened it and tried to see if there is movement but there is none.
At a guess, and it is that, it's likely out of level by half of or two thirds a sheet of paper.
How can I calibrate it further then this as both times I have had failed prints it has been the right side that had not adhered to the plate ?

Any one please :)

翻譯年糕

Thomassen Ølf
2019-04-06 14:56:54

Jason Croft
2019-04-06 14:58:11

Jeremy Lauzon
2019-04-06 14:58:17

Thomassen Ølf
2019-04-06 14:59:02

Thomassen Ølf
2019-04-06 14:59:30

Jeremy Lauzon
2019-04-06 14:59:34

Jason Croft
2019-04-06 15:05:20

Chris Visser
2019-04-06 15:13:01

Alex Varley
2019-04-06 16:56:39

Blaine Tsukayama
2019-04-06 17:33:29

Guti Gutmann
2019-04-06 17:43:40

Ingo Strohmenger
2019-04-06 18:30:38

Ingo Strohmenger
2019-04-06 18:40:51

Tej Joshi
2019-04-06 21:27:15

Ingo Strohmenger
2019-04-06 22:57:09

Tej Joshi
2019-04-07 00:31:28

Ken Lim
2019-04-07 15:24:54

Michael J Fuller
2019-04-07 23:09:05

Ingo Strohmenger
2019-04-07 23:17:24

Pablo Roy
2019-04-10 01:24:28

Dirk Ossebaar
2019-04-11 01:44:20

Breno Azevedo
2019-04-12 12:14:57

Hanz Photoss
2019-04-12 23:38:38


原文網址 Jason Croft
2019-04-06 14:36:26

Today I got a failed print, first one that's really bad just the whole thing looked like it had come off the plate on one side.
So I think clean resin vat, reset to 0 and go again, this worked for my first (this is second) failed print.
I do the usual 10mm as far as I dare then 1mm, it stops at a certain height and refuses to move lower no matter what I do.
I even try and trick it by moving it up 10mm then down 1mm and then try more 1mms but it's the same spot every time.
So this can't have been the problem with the print due to it was actually on the plate but I have no idea where to go from here.
Photon-S had it two weeks used it for, yes I know it's a lot, 70-80 hours in that time.

翻譯年糕

Jeremy Lauzon
2019-04-06 14:40:57

Jason Croft
2019-04-06 14:41:18

Jason Croft
2019-04-06 14:45:10

Tiki ZBrush
2019-04-06 18:15:08

Jon Lamkin
2019-04-08 09:05:08


原文網址 Jason Croft
2019-04-01 17:08:28

I maybe missing something really obvious :)

I am trying to get a single support onto this model, but whenever I do it lifts it up to fit supports beneath it.
I manuall place one where I want it and when I go back to slicer it won't let me lowers it to "0" without removing supports.
I want this to be built flat to the plate.

Any help is massivly apreciated as I have really picked your brains recently :)

翻譯年糕

Paul Churchill
2019-04-01 17:26:58

Markus Schönfelder
2019-04-01 17:27:59

Baturalp Arslan
2019-04-01 17:30:00

Robert Mako Sharkey
2019-04-01 17:36:11

Jason Croft
2019-04-01 17:36:51

David Howlett
2019-04-01 17:55:23

Jason Croft
2019-04-01 17:58:25

David Howlett
2019-04-01 17:59:06

David Calle
2019-04-01 21:26:48

Jason Croft
2019-04-01 21:33:40

Andrew Wall
2019-04-01 21:52:16

Jason Croft
2019-04-01 21:53:28

David Rodriguez
2019-04-01 23:15:07

James Hendrix
2019-04-02 00:08:40

Jason Croft
2019-04-02 00:09:28

Joe Broggio
2019-04-02 00:27:05

James Hendrix
2019-04-02 01:22:28


原文網址 Jason Croft
2019-03-31 01:46:24

Hello, I am after something that will really show off the Photon-(s).
Does any one have a clasic statue or something similar that is very detailed ?
I keep trying Thingiverse but after looking at like 2 things it becomes unusablely slow.

翻譯年糕

Mark Simpkins
2019-03-31 01:59:58

Kevin McGuigan
2019-03-31 02:04:57

Michael Van Kesteren
2019-03-31 02:38:51

Michael Van Kesteren
2019-03-31 02:45:32


原文網址 Jason Croft
2019-03-30 21:06:29

Ok, I may have just learnt a harsh lesson. My last print did not print...

So I decide after 7 days now is the time to change my FEP, more then anything clean inside and see how it's done. Ok screws...lots of screws...seems a lot easier then I anticipated watched a video...finish and sucess

How ever there was what looked like a "smear" on the FEP and since the rest was like crystal I decide to wipe it with a paper towel..."oh no" I think it's smeared I'll give it a gentle rub and clear it up...

It's covered in what looks like tiny scratches how bad is this going to be as it is new and they are almost "cloudly" in appearence more then actual scratches ?

翻譯年糕

Yves Hacault
2019-03-30 21:13:35

Ed Wilson
2019-03-30 21:15:20

Jason Croft
2019-03-30 21:45:22

Jason Croft
2019-03-30 21:46:07

Rob Jansen
2019-03-30 22:14:20

Jason Croft
2019-03-30 22:17:36

Rob Jansen
2019-03-30 22:19:18

Sen Kun
2019-03-30 22:21:35

Sen Kun
2019-03-30 22:23:45

Jason Croft
2019-03-30 22:28:39

André Pereira Simões
2019-03-30 22:32:29

Jason Croft
2019-03-30 22:34:01

Jehú Paulín
2019-03-30 22:50:59

Jason Croft
2019-03-31 01:42:26

Rob Jansen
2019-03-31 02:12:14


原文網址 Jason Croft
2019-03-30 06:02:10

Ok so far my series of small walls has been fine. Then I print this, albiet this is angled, and I get these lines.

Also seems to have aquired some small particles, do I need to change the 99.9% stuff ?

*Edit* Aqua Blue.

翻譯年糕

Mark Wardle
2019-03-30 07:08:28

Jason Croft
2019-03-30 11:57:30

David McGyver
2019-03-30 12:16:26

Jason Croft
2019-03-30 12:17:46

David McGyver
2019-03-30 12:19:37

Jason Croft
2019-03-30 12:21:04

Jason Croft
2019-03-30 12:21:39


原文網址 Jason Croft
2019-03-28 15:40:35

ok I'm moving on from Tinkercad to Fusion 360, or trying to :)

In tinkercad you can "edit grid" so I have been doing so for the build area of my printer.
Is there a way to do the same with Fusion 360 as I keep getting lost :)

翻譯年糕

Jeremy Lauzon
2019-03-29 03:23:55


 

討論主題

全不選 常用關鍵字