Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Amauris Rodriguez
2019-03-01 00:34:31

Hi folks... another dumb question for you. I've been using large tupperware tub to clean the prints with IPA. Is it a good practice to continue to use the leftover alcohol?

翻譯年糕

Mike Tongue
2019-03-01 00:44:59

Eric Green
2019-03-01 00:45:31

Mark Wardle
2019-03-01 00:46:51

Amauris Rodriguez
2019-03-01 00:47:14

原文網址 Amauris Rodriguez
2019-02-26 08:01:39

So print #3 completed successfully. Kicking off a new print now...

翻譯年糕

原文網址 Amauris Rodriguez
2019-02-24 23:07:35

Well, my first print was a total failure. The upside was that it was totally easy to clean. What couple have happened? I leveled the bed as indicated. I may have poured too much resin into the vat but I’m not sure if this would be the cause. Any ideas?? Also, any recommendations for another resin that’s not so smelly would be greatly appreciated. Thank goodness I put the printer in the garage.

翻譯年糕

Nick Sugg
2019-02-24 23:10:52

Stefan Giudici
2019-02-24 23:14:26

Mike Foreman
2019-02-24 23:15:46

Tony Lentini
2019-02-24 23:41:25

Dani Rose
2019-02-25 00:51:56

GaryAnji Smith-Lambeth
2019-02-25 01:19:14

Amauris Rodriguez
2019-02-25 01:26:58

Richard Shapiro
2019-02-25 01:32:44

Dani Rose
2019-02-25 01:34:15

Dani Rose
2019-02-25 01:34:42

Amauris Rodriguez
2019-02-25 01:42:27

Amauris Rodriguez
2019-02-25 03:55:43

Richard Thomas
2019-02-25 04:18:18

Amauris Rodriguez
2019-02-25 05:45:21

Amauris Rodriguez
2019-02-25 05:45:28

Dani Rose
2019-02-25 05:51:07

Amauris Rodriguez
2019-02-25 05:52:04

Brandon Marcussen
2019-02-25 06:30:30

Amauris Rodriguez
2019-02-25 06:49:20

Brandon Marcussen
2019-02-25 06:52:03

Hector Felix
2019-02-25 15:22:21

Alan Crooks
2019-02-25 15:26:41

Brandon Marcussen
2019-02-25 15:39:35

原文網址 Amauris Rodriguez
2019-02-24 05:58:55

Hi... I'm still trying to get used to the Anycubic slicer. Any ideas why the software raises the print and add these supports? I'm doing auto supports by the way... Any advice would be greatly appreciated. Thanks!

翻譯年糕

Jon Piercy
2019-02-24 06:04:34

Amauris Rodriguez
2019-02-24 06:08:11

Susan Sioux Mercer
2019-02-24 06:08:53

Susan Sioux Mercer
2019-02-24 06:13:05

Clayton Keller
2019-02-24 06:21:54

Susan Sioux Mercer
2019-02-24 06:27:26

Dani Rose
2019-02-24 06:33:17

Amauris Rodriguez
2019-02-24 06:43:44

Amauris Rodriguez
2019-02-24 06:44:33

Susan Sioux Mercer
2019-02-24 06:46:34

Clayton Keller
2019-02-24 07:24:10

Susan Sioux Mercer
2019-02-24 07:25:56

Nikolas Willingham
2019-02-24 07:39:50

Dani Rose
2019-02-24 14:41:36

原文網址 Amauris Rodriguez
2019-02-24 02:07:41

Hey folks.. I live in South Florida and was wondering where I can find IPA locally. Thanks

翻譯年糕

Matt Tilson
2019-02-24 02:17:53

Milton Maxson
2019-02-26 09:39:43

Michael Tennent
2019-02-26 09:54:07

原文網址 Amauris Rodriguez
2019-02-14 05:52:42

Hi... Thanks for the add!! I'm new to dlp printing and just ordered the Anycubic. I would greatly appreciate any advice you may have for this type of printer. Thanks!!

翻譯年糕

Paul Churchill
2019-02-14 05:58:28