Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 John Lawler
2019-05-22 00:01:32

I've got a need to print parts that are "esd-safe" and I have several different FDM filaments I can use to obtain this but I'm wondering if anyone knows of a resin that's available that has esd-safe properties? I'd love to be able to crank these parts out on the photon since I need 40 of them and I can fit 3 at a time on the bed. It would also justify the purchase of another printer at work.

翻譯年糕

原文網址 John Lawler
2019-04-20 22:43:45

If my prints are sticking to the FEP am I too high or too low with my Z?

翻譯年糕

Zena Andreou
2019-04-20 22:46:54

Dean Simpson
2019-04-20 22:49:43

Niklas Nox
2019-04-20 22:58:18

Dean Simpson
2019-04-20 23:00:50

Niklas Nox
2019-04-20 23:03:17

Dean Simpson
2019-04-20 23:03:56

Dean Simpson
2019-04-20 23:05:22

Richard Burrell
2019-04-20 23:06:41

Dean Simpson
2019-04-20 23:07:22

Dean Simpson
2019-04-20 23:08:40

Richard Burrell
2019-04-20 23:09:15

Dean Simpson
2019-04-20 23:10:49

Dean Simpson
2019-04-20 23:11:24

Richard Burrell
2019-04-20 23:11:47

Niklas Nox
2019-04-20 23:11:59

Chad Elstad
2019-04-20 23:19:52

John Lawler
2019-04-20 23:43:26

Dean Simpson
2019-04-21 00:01:56

Stefan Giudici
2019-04-21 00:05:40

Stefan Giudici
2019-04-21 00:06:24

Dean Simpson
2019-04-21 00:18:27

Dean Simpson
2019-04-21 00:19:20

John Lawler
2019-04-21 00:23:42

Sebastian Finke
2019-04-21 01:28:55

Richard Burrell
2019-04-21 02:11:14

Dean Simpson
2019-04-21 02:25:43

Gary Houser
2019-04-21 05:08:54

Michael Earley
2019-04-21 05:10:34

Richard Burrell
2019-04-21 05:12:10

Dean Simpson
2019-04-21 05:12:46

Robert Silvers
2019-04-22 12:16:32

原文網址 John Lawler
2019-04-20 20:39:17

I’ve had my Photon for a little over 24 hours and I’ve managed to get some really incredible prints... HOWEVER... I’ve also learned what not to do when you get a print stuck to the FEP. I’ve learned the FEP really stands for FREAKING EXPENSIVE PLASTIC because I’ve already had to replace it and went to order more so I have them and ouch! The most frustrating thing isn’t the learning curve (I’ve been doing FDM for years and have 7 printers) but the fact that when I turned the printer off while replacing the FEP when I turned it back on the cooling fan was screaming at me with that all too familiar sound that everyone knows when you have a fan going bad. My question is will they send me a replacement or will I have to exchange the entire printer?

翻譯年糕

Sen Kun
2019-04-20 20:43:42

John Lawler
2019-04-20 20:45:02

Paul Churchill
2019-04-20 20:46:01

Che Fielding
2019-04-20 21:00:32

John Oomen
2019-04-20 21:00:39

Chad Elstad
2019-04-20 21:07:39

Peter Ede
2019-04-20 21:37:06

Darren Donovan
2019-04-20 22:12:15

Stefan Giudici
2019-04-21 07:13:39

John Lawler
2019-04-21 07:18:46

John Lawler
2019-04-21 07:29:29

Chris Comeau
2019-04-21 10:40:56

Stefan Giudici
2019-04-21 10:42:58

Chris Comeau
2019-04-21 11:02:39

Stefan Giudici
2019-04-21 11:03:41

John Lawler
2019-04-21 11:05:20

Stefan Giudici
2019-04-21 11:06:55

Brandie Rae Smither
2019-04-21 13:49:41

Gary Houser
2019-04-21 20:12:00

Gary Houser
2019-04-21 20:14:07

Chris Comeau
2019-04-21 20:21:18

原文網址 John Lawler
2019-04-20 04:29:15

I’m not new to printing but this is my first SLA printer. I printed numerous success prints but now I’m having problems. I will get to about 4mm into a print and it fails to continue. I will have about 4mm on the build plate and then there will be a cured layer on the FEP. Any ideas? I’ve went through and leveled numerous times but I don’t believe it’s related to leveling because the print starts fine but seems to have some kind of failure once it’s been printing for a bit.

翻譯年糕

Zena Andreou
2019-04-20 04:40:37

John Lawler
2019-04-20 04:53:22

Zena Andreou
2019-04-20 05:05:12

Elle Heilig
2019-04-20 10:22:30