Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Rianna Nandan
2019-10-16 10:31:08

any idea what would cause a line like this in only part of the print? cape has a horizontal mark but the rest of the dude turned out perfectly. not a huge deal since i prime + paint over it, but how to avoid? printed on elegoo grey, 10s exposure, at a 15° tilt

翻譯年糕

Zachary Ford
2019-10-16 10:34:08

Alex Christiansen
2019-10-16 10:34:44

Rianna Nandan
2019-10-16 10:36:35

Andy Bulloch
2019-10-16 10:47:55

Wilfred Hdez
2019-10-16 10:54:09

Hugh Jeriolas
2019-10-16 13:15:59

Greg Chapman
2019-10-16 14:35:29

Brett VanDyke
2019-10-16 20:25:25

Diego Gonzalez del Rio
2019-10-16 23:12:45

Derek Reihe
2019-10-17 01:15:32

Zach Harris
2019-10-17 11:23:59

Dragut Gruia Matei
2019-10-17 15:02:14

原文網址 Rianna Nandan
2019-06-07 14:52:38

combine needlefelting and 3d printing to make the Ultimate Final DND Boss.

had my photon for a week and its so cool! cat was a gift from a friend haha.

STL from printedobsession on myminifactory: https://www.myminifactory.com/…/3d-print-eye-terror-32-mm-m…

翻譯年糕

Drake Noffsinger
2019-06-07 14:55:49

Rianna Nandan
2019-06-07 14:58:23

Drake Noffsinger
2019-06-07 14:58:44

Chris Wilander
2019-06-08 02:23:43

原文網址 Rianna Nandan
2019-05-31 02:44:08

printed the test cube perfectly annnnnd then.... immediately dropped it ?

翻譯年糕

Raphaël Gerber
2019-05-31 02:55:01

Adalberto Rodriguez
2019-05-31 03:11:30

Dominick Trascritti
2019-05-31 03:14:21

Devin Dahl
2019-05-31 03:17:22

Greg Young
2019-05-31 03:19:02

Robert Small
2019-05-31 03:19:23

Michael Van Kesteren
2019-05-31 03:22:14

Grant Weaver
2019-05-31 03:24:06

Stephan Lombard
2019-05-31 03:32:02

Fabio Ferrari
2019-05-31 03:53:51

Milton Maxson
2019-05-31 04:07:45

Chad Elstad
2019-05-31 04:20:18

Marvin Tomizzi
2019-05-31 04:26:25

Lou Steinritz
2019-05-31 08:01:34

Rob Young
2019-05-31 08:16:31

陳小鎬
2019-05-31 12:55:17

Zena Andreou
2019-05-31 15:56:47

Nick Wells
2019-05-31 15:57:51

Gary Houser
2019-05-31 20:56:15

Paul West
2019-05-31 21:42:44

Gary Houser
2019-05-31 23:00:07

Devin Wallace Simonsen
2019-06-01 00:28:34

Ike O'Ohiocaigh
2019-06-04 03:44:50

原文網址 Rianna Nandan
2019-05-27 05:33:54

hello! i'm new to this - if there are unsupported islands in the hollow portion of a model, what's the best way to go around solving them?
also, if printing something flat to the plate, can I put the hollowing holes right on the buildplate, or do they have to be up higher?
thank you!

翻譯年糕

Richard Thomas
2019-05-27 05:51:09

原文網址 Rianna Nandan
2019-04-23 07:48:12

Hi there! I'm looking into getting a photon v1 for printing paintable minis, really impressed with the print quality from what i've seen. However I do have two questions:

1 - How difficult are the supports to remove as compared to an fdm like ender3? Will a hobby knife be sufficient?
2 - Whats the best way to ventilate it in a smaller space / apartment? i've seen setups where people either vent it out the window or through a growtent filter, would either of these be sufficient for use in a bedroom?

Thanks!

翻譯年糕

Tori Beckett
2019-04-23 07:53:11