Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Jim Brown
2019-06-12 06:22:18

Well, let's see how this goes.

Luke Mason
2019-06-12 08:32:22

原文網址 Jim Brown
2019-06-10 11:23:07

What setting generates supports between supports in Chitubox? I like to manually generate supports but sometimes supports between supports would be helpful? (Especially tall supports)

翻譯年糕

Luke Mason
2019-06-10 11:43:11

Jim Brown
2019-06-10 11:44:40

Luke Mason
2019-06-10 11:47:43

原文網址 Jim Brown
2019-06-09 23:46:29

Need some opinions. I picked up Elegoo gray (not the quick set version). At 60 seconds exposure on 8 base layers, 13 seconds on the normal layers, I’m not getting bed adhesion. No nice “thunk” noise etc. I bumped bottom exposure up to 80 seconds. on a very small print that I just started I heard the magical “thunk” noise in the base layers.The ambient temperature here in Juneau is in the upper 50s. Are longer exposure times needed in lower temperatures? The build plate is level and adjusted.

翻譯年糕

Bob Deblier
2019-06-10 00:01:17

Jim Brown
2019-06-10 00:05:25

Bob Deblier
2019-06-10 00:06:57

Alex Clarke
2019-06-10 00:19:39

Jim Brown
2019-06-10 01:30:58

Todd Jones
2019-06-10 07:57:47

Jim Brown
2019-06-10 07:59:14

原文網址 Jim Brown
2019-06-09 11:27:54

Is there a way to adjust the 0 layer up by 0.02mm without going back through the entire calibration process? I used the Flint Reed method but set it a little too low.

SOLVED: So I think I stumbled upon the best way to level the build plate and set the z=0 height. I use the Flint Reed method to LEVEL the build plate, then I use the paper method to set the z=0 HEIGHT. :)

翻譯年糕

原文網址 Jim Brown
2019-06-08 10:43:59

原文網址 Jim Brown
2019-06-07 12:53:31

So happy with the new in-line fan and carbon filter. I can stand right next to the printer now and no smell. Zero. ? Credit goes to Nick for this system, it rox!

翻譯年糕

Mario Toy Rossi
2019-06-07 15:03:55

Cezar Gheorghe
2019-06-07 18:54:36

Matt Goody Goodrich
2019-06-07 20:13:30

Mason Chapman
2019-06-07 20:27:14

Cezar Gheorghe
2019-06-07 20:31:57

Chad Elstad
2019-06-07 20:49:53

Marc Breitman
2019-06-07 22:22:11

Josh Thomas
2019-06-07 22:48:02

JD Grimm
2019-06-08 01:54:44

Franz Funk
2019-06-08 02:27:22

JD Grimm
2019-06-08 09:59:29

Melecio Guzman
2019-06-08 11:14:20

Melecio Guzman
2019-06-08 11:15:45

Melecio Guzman
2019-06-08 11:16:27

Jim Brown
2019-06-08 11:17:20

Melecio Guzman
2019-06-08 11:17:51

Jim Brown
2019-06-08 11:17:52

Jim Brown
2019-06-08 11:18:35

Melecio Guzman
2019-06-08 11:19:45

Jim Brown
2019-06-08 11:21:29

Anton Richardson
2019-06-08 20:33:39

E Spencer Schubert
2019-06-11 10:00:06

Mothy Reynolds
2019-06-11 10:19:38

Chad Elstad
2019-06-11 21:08:40

Michael Steadham
2019-08-09 08:37:41

原文網址 Jim Brown
2019-06-02 08:54:35

Today’s prints. ?

翻譯年糕

Luke Mason
2019-06-02 09:17:58

Jim Brown
2019-06-02 09:28:20

Elle Heilig
2019-06-02 09:42:56

Jared Rutledge
2019-06-02 10:41:51

Jim Brown
2019-06-02 10:49:38

Jared Rutledge
2019-06-02 10:53:47

Jared Rutledge
2019-06-02 10:54:03

Jim Brown
2019-06-02 10:58:25

Stephen Farrell
2019-06-02 12:01:56

Octavio Carlo
2019-06-02 12:20:41

Joel Reid
2019-06-02 12:45:51

Cody Raskin
2019-06-02 13:17:31

Luke Mason
2019-06-02 13:47:14

Sebastien Verbiese
2019-06-02 18:36:59

Chris Baker
2019-06-02 23:03:12

Jim Brown
2019-06-03 02:06:25

Cody Raskin
2019-06-03 03:40:19

Yamil Hugo Corco
2019-06-03 03:45:08

Jim Brown
2019-06-03 07:21:56

原文網址 Jim Brown
2019-05-30 11:33:50

So by default light off delays are set to zero, how do these settings effect the quality of prints? I have left them at zero until now; the resin spreadsheets usually have them somewhere around 1 second.

翻譯年糕